Element ELCFW329

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • hbdeals
    Senior Member
    • Oct 2014
    • 55
    • USA

    #1

    Element ELCFW329

    32" Manufactured January 2013. The red light comes on when plugged in. The power button does nothing. There's no clicking sounds. There's a very faint high pitch noise coming from the power board.

    All voltages are there except the 24 volt is showing about 12 volts. One odd thing is that the meter shows 24 volts for a millisecond when the leads are first applied. I tried unplugging each connector, but no change in behavior.

    Any ideas on what to try next?





















































  • hbdeals
    Senior Member
    • Oct 2014
    • 55
    • USA

    #2
    Re: Element ELCFW329

    I got it to power up after heating the winbond flash chip. I think the 24v is mislabeled on the board because those pins have a jumper wire to the 12 volt side from the factory.

    Comment

    Related Topics

    Collapse

    • flysky
      Gigabyte H610M S2H V2 help to identify the element.
      by flysky
      There is a motherboard Gigabyte H610M S2H V2 (DDR5), I can't find boardview
      Help to identify the element, marking on the element - C31PH. It stands next to the USB 3.0 and it looks like it is ESD Protect chip. We need a datasheet to this element. Maybe someone has already identified such an element. Help please.​






      ...
      01-23-2025, 07:21 PM
    • MisterAIL
      PS5 digital / No Power / No Beep / Good power supply
      by MisterAIL
      Hi everyone,

      Brought a non functionnal PS5. Apparently only a bad PSU...
      No beep, nothing.

      After some tests i found this :
      - PSU is fine (12 volts stable)
      - 12 volts line is shorted
      - DA9065 was fried, F7003 also => Replaced both of them, short is gone on 12 volts line, no dead short anywhere else.
      - By the way, nothing change. No signal, no power, no beep.

      Mesuring all rails with my workbench psu (12 volts input)
      - 0.00 amp drawing
      - 12 volts, 5 volts, 2 volts, 1,15 volts are presents (suppose new DA9065 do is...
      03-12-2024, 03:24 PM
    • sam_sam_sam
      Heater element wire type instead of a fuse when troubleshooting a short circuit DIY
      by sam_sam_sam
      I was Ollie today which is a close out / surplus outlet store I do not go in there to often because you find things that you should not be tempted by but that is a another story

      I saw a small space heater that used a wire type of heater element which I been looking for a while but not really hard mind you but when I saw this I grabbed it I going to go back tomorrow and buy the last one that is like the one I bought today because I need the heater element and the ceramic insulators and more of heat element wire because this one has two different wattage settings one 1300 watts ( tap...
      12-16-2023, 08:39 PM
    • BTubbs200
      Dead Dell Latitude 5420 not receiving 20 volts from USB-C charger
      by BTubbs200
      Hello,

      Dell Latitude 5420 P137G
      Board: LA-K491P REV A01

      I have received this laptop which was described as "does not power on or accept charge." Battery shows no sign of charging when charger is plugged in, nor does the board show any signs of life when battery is unplugged and charger is plugged in. No light from the LED at all or any other indications of activity.

      Board seems to have no shorts, all power rails are fine and show high resistance.

      When charger is plugged in, voltage is present in 3.3V rail but absent in others....
      01-24-2025, 08:15 PM
    • sam_sam_sam
      MPJA 10 AMP @ 0 to 30 Volts Switching Power Supply Cap Fault
      by sam_sam_sam
      I have this 10 amp 0 to 30 volt switching power supply that decided to have a 630 milliamperes draw on it at 0 volts

      I open it up to find non brands name capacitors in it

      I am not sure how this switching power supply is set up

      Could someone please explain how this power supply works

      Here is the capacitor ESR results

      (1) 47uf@50 volts 0.46
      (2) 47uf@50 volts 0.45
      New 47uf@50 volts 0.35

      (1) 100uf@25 volts 0.34
      (2) 100uf@25 volts 0.35
      New 120uf@50 volts 0.08

      (1) 220@25 volts 0.13...
      10-21-2018, 10:02 AM
    • Loading...
    • No more items.
    Working...