I need help identifying a part for replacement, the mainboard i have has a burned component, unidentifiable markings incidentally, i have found a pretty clear image of the component but cannot find any information about it, can someone identify this part? Its in location qa6.
coby led4626
Collapse
X
-
Tags: None
-
Re: coby led4626
Looks like a mosfet to me for the panel-VCC used as a switch. Maybe a P channel Mosfet. Something like a AO3407. https://cdn.badcaps-static.com/pdfs/...b1f6ab665c.pdf Not that I am saying it is that exact replacement for it, as I can't read either what the picture is saying. But if push comes to shove, this is better than nothing.
I wonder if your panel is shorted?Last edited by CapLeaker; 08-26-2016, 07:26 PM. -
Re: coby led4626
QA6?
Do you have 12V at either end of the Inductor L60?
That device has to be able to handle at least 5A or more. You can look up the spec sheet of the LCD panel to find out what the inrush and the running current of the TCON is needed.
And as mention, you should check the fuse on the T-CON board and the resistance between GND and the output side of the fuse to see if there is shorted circuit there.Last edited by budm; 08-26-2016, 07:47 PM.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Comment
-
Re: coby led4626
Check the resistance between the chassis GND and either end of the T-CON fuse, notes: it may have active shorts that will not show up until the circuit is turned on.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: coby led4626
The resistance is .1 ohms, when i test for a short with power off there is no short, when i test with power on it shows a short on both sides of the fuse. should i have everything hooked up when testing? The only thing not hooked up while testing is the panel, and the inverter board. I still havent identified the original burned part either.Comment
-
Re: coby led4626
Don't test reisitance with power on. You'll damage your meter and possibly the circuits.Willing to help but I'm no expert.Comment
-
Re: coby led4626
Man, people need to learn how to use test equipment properly before trying to work or fix something, otherwise we will get wrong information or the Operator may get hurt in the process.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: coby led4626
Did i do sometging wrong here? I thought you wanted me to test the tcon board for short, specifcally with the power on.Comment
-
Re: coby led4626
I tested one side of the fuse at a time, and used one of the grounds on the board. I did not put my meter to both sides of the fuse and test restance while there was power. I use caution when working with live equipment or recently used electronics. If i did something incorrect, please point it out.Comment
Related Topics
Collapse
-
by crosswindsHello,
So, pulled a motherboard out from storage, was working when put away, wont post when I took it out of storage today.
Since it was working, and it looks to be essentially time that killed it I figured its a good idea to replace the caps before digging further.
Looks to be only good quality caps on this board, so might not be the issue. But it is closing in on 20 years now so, wont hurt i guess
Its a ASUS P5VDZ-MX board.
I would really appreciate some assistance on what the best replacement caps would be for these:
Panasonic(M)...-
Channel: General Capacitor Questions & Issues
-
-
by sauroHi,
I am trying to find a replacement for this IC (USB Controller) but not having much luck in finding the data sheet for it. Chip Code - BAC7KG - PU1502 part on a "Bucks U42 DIS 17817-1" motherboard.
Many Thanks.
... -
by Rashid36Lenovo Legion Silm 5 16iRH8
LA-M542P
REV 1.0
any body can share schematic or decode it....
Help me out2 Photos -
by fytonvMy 7 channel NAD receiver has audio quality and volume issues on 2 of the channels. Sometimes they work and sometimes they don't. Sometimes they're at about half the dB level of the left channels, and then they cut out entirely. Powering off and on the receiver fixes it for a bit.
Without much experience to really know for certain, they only apparent issue I can see is with these electrolytic capacitors on the power supply. Bulging = bad, correct? I'm looking for replacements but I'm unsure what leeway I have with the temp ratings. Are there any other specifications I need to worry...-
Channel: Troubleshooting Audio Equipment
-
-
by the_remHello guys,
I would like a quite old but still good 800 W ATX PSU to be repaired. The problem was an extremely heavy coil whine coming from the small secondary transfomer on the PCB.
I desoldered it hoping the references on the upper side would allow me to find a adequate replacement part. Sadly the written references drove me nowhere but to the manufacturer (I-MAG). I sent them a message like a bottle in the see asking them to send me a datasheet of the transformer. And... They responded ! I received a kind of datasheet (see attachment) but my competencies do not allow... - Loading...
- No more items.
Comment