Urgently need a used panel for this tv. Must be in the UK. Anyone got one??
Panel Needed!: Hitachi 42hxt42uh
Collapse
X
-
Re: Panel Needed!: Hitachi 42hxt42uh
Is it cracked ? Also WNDL is an Lg 42" Fhd panel, the model should be near which is on another stick can you get an image ?Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/ -
Re: Panel Needed!: Hitachi 42hxt42uh
Lol epic fail, tbh how you crack it ? I have been quite rough with some panels not yet cracked one haha and fixed nearly 500 Tv's sorry to sound big headed
Anyway the Lg panel model number will be on a sticker and something like LC420WXU SF E1Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/Comment
-
Re: Panel Needed!: Hitachi 42hxt42uh
and you just cursed yourself.
Comment
-
Re: Panel Needed!: Hitachi 42hxt42uh
Fakkkkk. I knew i took it off with care and place it on a flat surface with care so not sure i did it or no one is admitting to anything (coworkers).Full-time computer repair tech (10am - 6pm) and full-time, (8am - 11pm), Ruby on Rails Developer
Comment
-
Re: Panel Needed!: Hitachi 42hxt42uh
No other sticker. On the metal bit i see:
mb95 fhd-lg2d
42180 dledFull-time computer repair tech (10am - 6pm) and full-time, (8am - 11pm), Ruby on Rails Developer
Comment
Related Topics
Collapse
-
by howardc6449UJ6500 LCD panel has a lighter band on top when first powered on. Goes away (or gets much fainter) after TV on for a few min. After powered off for awhile and power back on, same band appears. If powered on immediately after powering off, no or much fainter band. Running the latest firmware.
Disassembled the TV and lifted the LCD panel during testing. Band is on the LCD panel (can see the band on the panel as I lift it slightly) Backlight is perfectly even at the top edge. Double checked LCD panel alignment in the frame and is perfect but since band moved with the panel, its on... -
by OKRPKCOMPI have a dell pc with corrupt bios during bios updation
OptiPlex Tower 7010
Service Tag 4M19QY3
board code TD0201 REV A00
D13 Entry Opti Low 222999-1
motherboard fan spins and off after some seconds
backup attached here...-
Channel: BIOS & Schematic Requests!
-
-
by jorpecHi, all
I need the dump/firmware for this tv, it was on a boot loop, i dont have the original corrupted dump because i used a pen drive with a firmware that solved the boot loop, initially it seemed it was ok but the tv has no sound
Thanks10-17-2025, 03:51 AM -
by triplefourTV flashes backlight then reboots over and over. no image. Client said it used to have image for a bit before rebooting. Got worse over time.
tcon is built into mainboard.
Only one cable goes to panel boards.
there is a cable from one panel board to the other that links them.
cost cutting measure that results in us having harder time to diagnose.
removing the link to the second panel board allows TV to stay on with stable backlight but no image.
used cut off tape method to mask 1 maybe 2 pins on the side of the cable that goes to that second panel board.... -
I had a the above tv qn55q60r that had a bad panel but everything else good. I had another panel here from un55nu6900 with bad leds and melted diffusers.
I put the nu6900 panel in and powered it up and it does work but there are lines vertical lines.
I was trying to change the panel type in the service menu but don’t see my exact panel. Anyway to fix this or someone have similar experience.
the clear picture is the panel type from the service menus on the nu6900. The other 1 is the panel type that was set for the q60r with the bad panel....01-13-2024, 01:57 PM - Loading...
- No more items.
Comment