LG 50PG3000, left half of the screen black, right half colours washed out.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • jczarniak
    Senior Member
    • Oct 2015
    • 179
    • UK
    #1

    LG 50PG3000, left half of the screen black, right half colours washed out.

    Hi,
    I switched on the television yesterday.
    Left hand side of the screen was black, right hand side OK.
    After couple of minutes, left half of the screen still black but right half of the screen lost the resolution and colours has changed to washed out.
    Where should I begin with troubleshooting, please?
    Thank you for any support.
    Attached Files
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • kca
      LG 82UN8570AUD ~ TCON or PANEL?
      by kca
      Hello all ~

      Hope this finds you well. This LG 82UN8570AUD (April 2021 model) 4K UHD television has full audio capabilities but video is compromised / problematic.

      When I picked up this large LG tv it had a full black screen upon startup. Previous owner said it just went black one day. No popping sound or anything else of note.

      I got the display to work by taping off several traces of the right-hand side ribbon cable on the TCON that leads from TCON to PANEL. However, despite dozens and dozens of attempts to find the right combination / range of traces taped...
      08-31-2025, 06:38 AM
    • armoured_smiler
      Panasonic Tx-40cx400b top left half screen not displaying correct
      by armoured_smiler
      Hi,

      Trying to work out if this is TFT problem or TCon issue.
      The TV powers up but the top half of the screen, from the right it is OK, but as you look across to the left halfway across it starts get duller and duller until it is very dark on the lefthand side, currently I trying to clean the remote as it seems to have something film wise on the pads stopping it from registering buttons pressed.

      Also when changing the screen size of Windows PC display to say to a smaller pixel sizewindow, the original window displayin the top left stays/takes a few seconds to disappear?...
      2 Photos
      04-08-2024, 03:40 PM
    • Zelek11
      Panasonic Plasma screen interference on left half of screen
      by Zelek11
      My Panasonic Plasma model P55VT50 has started displaying "interference" on just the left half of the screen only (left when facing the screen). Sometimes it's concentrated in about the first 30 seconds after startup, then disappears. Other times it's fine at startup and then randomly does it later on. When it flashes the interference it's very quick and doesn't stay on the screen unless it flashes repeatedly in a row.



      This image is a screen shot from a video I took. This is an example of the interference at its worst. Often the interference is much smaller...
      10-14-2022, 04:54 PM
    • howardc64
      TCL 49S405 double image
      by howardc64
      LCD displays a 2nd image slighty offset vertically. And multiple pairs of black lines along the bottom. Probably common as google "TCL 49S405 double image" pulls up this ifixit post ( link ) with identical ( nearly, but their fault seems to be on the other half of the panel than mine ) problem without solution.

      This one looks to be a more difficult to diagnose because most? of TCON seems integrated ( CSOT BGA on buffer baord) into the left panel edge board ( looking from rear of TV) There are 2 buffer boards for each 1/2 of the screen. Main connects to the left buffer board...
      06-23-2025, 03:20 PM
    • microvibe
      Panasonic Th-42px75u top half white washed
      by microvibe
      I have a th-41pc75u top half screen washed out can see menu etc vaguely in the whitewashed top half and fine in bottom half. Tv shuts off after few seconds 7 blinks. I disconnected one of the panel ribbons for top half tv will stay on still white washed except for the disconnected ribbon thats black. I tested the su board but cant find a short maybe tested wrong. In the sc board i did notice the white ceramic 2.2k ohm is burnt would this cause this issue or is it still buffer issue....
      10-16-2019, 11:31 PM
    • Loading...
    • No more items.
    Working...