Panasonic TC-P42ST30 14 blinks.

Collapse
X
Collapse
 
  • Page of 3
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 template Next
  • Malachi
    Badcaps Legend
    • Dec 2015
    • 1077
    • Usa
    #41
    Re: Panasonic TC-P42ST30 14 blinks.

    I don't have another tv to test it in.
    I picked up today for $25. The owners were moving, cracked the tv in the move and bought a new one.
    They said it was working up till they moved.
    I'll try to check the c-board this week.
    I know one of the SN ribbons needs reseated as I can see some horizontal lines but since that was my first try, I thought it was pretty good.
    No point spending 30 minutes with it if the other problem isn't fixable.
    Unless it's to make sure the SN board works.

      Comment

      Previous 1 2 3 template Next

      Related Topics

      Collapse
      • Andre Gilbert
        Panasonic TC-P55ST50 8 blinks then no blinks
        by Andre Gilbert
        Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here🤔?
        Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting 😂.

        TV Model: Panasonic TC-P55ST50
        ...
        1 Photo
        11-20-2024, 08:52 PM
      • nobbnobb1
        Panasonic TC-P50U50 Powers Off - 8 blinks
        by nobbnobb1
        Hello,

        I have a Panasonic TC-P50U50 plasma TV which powers on briefly, then powers off and flashes the power light with 8 blinks. This TV is infamous for this, of which the suggestion that the SS board has failed due to loose grounding screws and requires a replacement of the following components on the SS board:

        2x DG302 (Q16051)
        2x RF2001 (D16041)
        2x 5.6 ohm SMD resistor
        1x BD8694 IC

        I have already gone ahead and replaced these components, as well as cleaning off the ground connections on the SS board as well as the associated...
        03-21-2023, 08:33 PM
      • BigPete
        Panasonic Heatpump Dryer Repair
        by BigPete
        I picked up a Panasonic NH-P70G2, though it would apply to the NH-P80G2, NH-P70G1 and NH-P80G1 models as well, as maybe some other models. This one was coming up with a H86 error. After lots of testing and googling it was an error with one of the thermistors in the condenser area.
        The attached French service manuals is incorrect, TH11 is gray and is a 95k thermistor and TH12 is black and is a 35k thermistor.
        In my case TH12 was bad. I was able to get a 35k thermistor on AliExpress. It's 6mm in diameter.
        Unfortunately the whole machine has to come apart to fix it.
        I have...
        11-01-2025, 06:40 PM
      • mmischni
        Panasonic Viera Plasma TH-42PX75U 7 Blinks/8 Blinks/burned P board?
        by mmischni
        Greetings friends,

        I have a Panasonic TH-42PX75U manufactured in 2007. It has been trouble-free until recently. One evening I turned it on and it then powered back off and gave 7 blinks.

        First a question about the blinks. Everyone only speaks of a single number of blinks. I noticed on my TV, it blinks one fewer times for the first group of blinks, then blinks the full number repeatedly. So for my first code in question, the TV switches off, blinks 6, then blinks 7 repeatedly. When I disconnected the SC board, the TV switches off, blinks 7, then blinks 8 repeatedly....
        09-06-2017, 08:52 PM
      • dj01fad
        panasonic tx-p50gt30 8 blinks afrer 7 blinks repair
        by dj01fad
        Hello again.

        I have a little problem with my tv: it had the 7 blinks failure, and I repaired the SC board. After that, it starts for 1 second and goes to 8 blinks. Everything on the SC board looks to be fine but I discovered that I have one shorted transistor on the SS board, Q102. I have a new one but I am wondering if it would be better to replace also IC 191.
        I did not check the SS board before the 8 blinks. Do you think it's possible that it went off together with the SC board or it died after my repair?
        10-25-2020, 06:05 PM
      • Loading...
      • No more items.
      Working...