Re: Telefunken T32TX182DLBP NO Turn on - Blinking LED
It doesnt matter if its for your menu the core update works on all 17mb82 and 95s boards.
-
Re: Telefunken T32TX182DLBP NO Turn on - Blinking LED
I searched this site http://www.vesteldriver.com/
but i cant find a matching code to my service menu. :/
So i cant find the file to flash..any help here?Leave a comment:
-
Re: Telefunken T32TX182DLBP NO Turn on - Blinking LED
You need to find the core update file on the internet then reflash that. Guessing you didnt watch all the video as it shows me doing that
Leave a comment:
-
-
Re: Telefunken T32TX182DLBP NO Turn on - Blinking LED
Hello did you watch my video on how to repair the 17mb82 firmware ? Might need the firmware to be reflashed, if not I will link it.Leave a comment:
-
Telefunken T32TX182DLBP NO Turn on - Blinking LED
Hello Guys,
I own this TV for the last 2,5 years (~380 days uptime).
The TV refuses to turn on and returns an infinite blinking LED.
It only boots up by itself when the power cord is reconnected to the power source repeatedly, while the antenna cord is removed.
After watching MrReeceyburger123's troubleshooting videos on YT, I checked the Power Supply (Vestel 17IPS19-5) for shorted Diodes, but none off them gives a beep sound to the multi-meter..
I also tried to Reset the TV via the service menu but no luck.
The TV Works fine for hours, if a successful boot happens.
but a power off causes blinking LED and no power on..
Is there anything i should investigate more?
Looking forward your advice..
Keep up the good work!!
Attached Files -
-
Hi everyone,
I've got this LG TV here that wouldn't turn on and be stuck in a standby loop (blinking red once every other second).
Did test the following:
* LED's seem fine as they all light up using LED Tester
* Power Supply supplied around 111V for each LED Strips (2x edge lid strips)
* PWR_ON would be at around 3V but dropping every other second (just like the standby light)
* DRV_ON is doing the same
* power supply has a green LED onboard, but that doesn't seem to do anything (stays off the whole time).
* there is a tiny clicking... -
Hi there,
I have this ASUS X453MA Laptop that's not turning on. When I plug in the charger, the green light just keeps on blinking and pressing the power button does nothing.
I have checked the charger and it is giving 19+ V
I have disconnected the battery and pressed power button for 30 seconds.
I tried another RAM stick.
Tried disconnecting the keyboard and touchpad.
Tried disconnecting the HDD and the wifi adapter.
The problem persists.
Hope you could help me out on this one. Thank you.12-14-2024, 06:40 AM -
Hello, i have some issues with my laptop Lenovo Y700-17ISK (motherboard BY511 NM-A541), it started when i turn on the laptop, but the lcd wont turn on, i then connected it via hdmi to tv and screen was ok. So i thought maybe lcd stripe is faulty, i removed the bottom cover, disconnected main battery, reset the cmos by disconnecting battery for 1 min, then slighty move the lcd stripe. Conncted power supply and tuned on my laptop, the lcd turn on, it started to load os, then it turn off, after a second it turn on, then after like 3 seconds turn off again, and so on. Removed power supply, waited... -
Telefunken D50U600M4CW
Mainboard Vestel 17mb130s 23527519
Panel VES500QNDC-2D-N15
NAND Flash Memory 29F4G08ABAEA
SPI Flash 25L1606E
Hello everyone, I need help, there is a Telefunken D50U600M4CW with a problem that does not turn on, the duty LED is flashing red.
All voltages are present on the power board, I tend to the version that the firmware has flown. I read the dump from SPI Flash 25L1606E, as I understand it, it is broken.
Can anyone share a dump for SPI Flash 25L1606E or fix it, or if possible, is there a firmware for this model.
...11-28-2022, 04:39 AM -
Hello
I was looking for a schematic or board view but unfortunately I didn't find anything.
By connecting the drain and source of pq58, the device turns on and works perfectly, but the battery doesn't charge, and I don't know the path of the circuit to the MOSFET.
Is the problem with the adapter? Or is there a problem with the MOSFET activation circuit?
Please guide me.
Thank you.
Leave a comment: