Hi, everyone. It been quite some time I don't start a thread, most of the time you can find the information in the forum. I look for my problem but still have some doubt . I got a Lg 60pk550 from a friend that was going to get rid off. The tv turn on and off in a continues circle, you can see the screen when it on but will immediately shut off and start all over again. You can hear a click when it turn on and almost immediately another click and shut off. I have unplug each board, one by one, plug the tv, still same thing, two click and go into circle. The only board that it does only one click is when i disconnect the main board. I am incline to believe that i have a bad main board. I have put some picture of the back of the tv. If some one can help me it will be really appreciate.
LG 60pk550 turning on and off
Collapse
X
-
Re: LG 60pk550 turning on and off
Ok so leave the resistor in place just now.
Disconnect the LVDS cable that connects the Main AV Board to the Control Board (t-con).
Now with a paper clip or piece of wire connect the 2 holes on the control board marked EXT_AUTO_GEN
If it's not marked, it's usually 2 holes beside R51 and R52, or R501 R502.
Your picture isn't of good quaility but I think the 2 holes are located here:
Plug in the tv, it should now power on and display test patterns.
Does it?Comment
-
Re: LG 60pk550 turning on and off
Good morning. I am more awake now. Ok, you are right, vs 200 and va 59. The issue is that i get that without having the resistor put on but in both cases with it on or off the voltage drop. still hear the two click. The test that you mention i already did it last night and nothing happen, still hear the two click sound. in the first click the tv will start and you can see a white screen immediately it click again, it turn off. It will not stay on.Comment
-
Re: LG 60pk550 turning on and off
I did as you said. I put the two resistor 5vstby to RL-ON and 5stby to M-ON but still wont stay on. I am going to take a picture of the power supply back and front to see if you can see something that i may be missingComment
-
Re: LG 60pk550 turning on and off
the problem is your power supply isn't staying on.
I can only give you advice but really finding the problem will be down to your own fault finding ability.
Check and make sure that all voltages going to the main AV board are present (17v etc) and not fluctuating.
Reflow all joints on parts attached to heatsinks. Resolder transformers and coils.
The 50" versions of these Tvs suffer from either one of the 3 wirewound resistors failing (located in top right of the power supply.) test them and make sure they are in spec.
It could be a faulty regulator, these can sometimes be easily found with a can of compressed air turned upside down and freeze them. If the power supply turns on and stays On with them frozen then change it out and best to change any parts in circuit with the regulator.
The smaller caps on lgs fail all the time but will look good. Try heating up the caps with a hair dryer then applying power once they are hot.
Good luck.Comment
-
Re: LG 60pk550 turning on and off
Good Morning Hamie. Thank you for reply. This is all very interesting, I don't know much about technology but i am a quick learner and i like challenge. You had give me plenty idea of what to look for. I will follow your instruction step by step. I am looking forward to give you good news. Will keep in touch, once again thanks.Comment
Related Topics
Collapse
-
by m1ch43lzmHi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic... -
by YanlebHi all, I just want to share the repair of my 60PK550-UA TV set.
The TV set was powering on, just no image. After verification, nothing wrong on the YSus or ZSus boards. Nothing wrong on the main board either.
But I noticed that the LED was not flashing on the Logic Control Board. This is an EBR63450301. The LED is supposed to flash even with all the flat cables disconnected, with only the power cable attached.
All the voltages measured at the electrolytic capacitors on the board were good. From top left to bottom right:
C57: 3.30V
C61:...07-20-2023, 12:38 AM -
Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?by Tynan DillI was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.
Upon bringing it home and plugging it up, it showed a standby light.
I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.
The screen seems to blackout and stay black, but with a flashlight I can see the display.
With my Playstation 4 connected via HDMI, and running a game I can hear sound.
Assuming...7 Photos -
by HakuuHi There,
This TV was auto switching off after few seconds with some vertical lines on the screen, so got a new TCON board and replaced it.
After replacing the TCON board it was working fine and i set it up with everything, used for few hours, then had the bright idea to update the software on it. During the update process, TV switched off and now no audio or video. No relay switch sound.
More Details
TV Model - LG OLED77G1PUA
Got the same exact TCON board from TVPartsToday and replaced it. But didnt transfer the EPPROM data (didnt... -
by jb_BakHey guys great forum glad to have found it. I bought a Sony XBR 65X900C cheaply because it didn't work. No signs of life at all not even a light/led. All I hear is a brief high voltage sound when I throw the power to it.
Didn't see any obvious signs of damage so right away started checking voltages. This is what I see:
Power Board Connector that goes to Main board
CN6401
Pin 01 NC
Pin 02 NC
Pin 03 "BL_ON": 0V
Pin 04 "N/C"
Pin 05 "STBY 3.3V": 3.5V
Pin 06 "GND": N/C
Pin 07 "AC_OFF"... - Loading...
- No more items.
Comment