Sharp LC-70LE650 - Shaded on one side w/ line down middle

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • tech144
    New Member
    • Jun 2015
    • 9
    • US

    #1

    Sharp LC-70LE650 - Shaded on one side w/ line down middle

    Hello, I repairing a Sharp LC-70LE650U around 2 years old. And customer said one night while watching, picture developed line down the middle with right side having a noticeably darker shading. After it arrived in the shop, I noticed intermittent flickering of the shaded right side when first turned on. Then eventually picture on right side stays more shaded then left. Obviously, I checked the Tcon cable seatings and cleaned all contacts. Disconnected and reconnected several times, just to see if there is bad connections. But to no avail.
    I searched here other threads on the 70 inch Aquos but this set does not have any blink codes or protection shut downs. I see there is an infamous "tab issue" with this model also. I am not sure where to check to see if there is bad connections on these tabs. Any help is much appreciated.Thanks.
  • freakaftr8
    Badcaps Legend
    • Oct 2012
    • 3743
    • USA

    #2
    Re: Sharp LC-70LE650 - Shaded on one side w/ line down middle

    Picture of the fault?
    Did I leave the soldering iron on?

    Comment

    • budwich
      Badcaps Legend
      • Jul 2015
      • 3097
      • Canada

      #3
      Re: Sharp LC-70LE650 - Shaded on one side w/ line down middle

      Is the line horizontal or vertical. IF horizontal, then you are a likely "candidate" for the "saveable tab operation"... :-) IF its vertical, then :-( as it is likely a tab along the bottom which are not removeable to do a "save".

      Comment

      • tech144
        New Member
        • Jun 2015
        • 9
        • US

        #4
        Re: Sharp LC-70LE650 - Shaded on one side w/ line down middle

        Sorry no pics, and the line was vertical.........update! I found left t-con cable to panel had corrosion on the female cable terminal (The jack that the cable plugs into on the panel side). At first, when I initially observed the cables and the jacks in that area, I did not see it because it was hidden. So I ordered a ribbon cable off ebay and cleaned in extreme detail. I will give update later when cable arrives.

        Comment

        • tech144
          New Member
          • Jun 2015
          • 9
          • US

          #5
          Re: Sharp LC-70LE650 - Shaded on one side w/ line down middle

          Update...the ribbon cable fixed the vert line and flashing problem!! But Not out of the woods yet.

          I had it testing for most of the day, and when I came back to it....it was the "2 blink slow- 2blink fast" error code and shut down. According to the manual, that's a "DET13v_ failure". OK..what I do know there is standby 5volts from PWR supply getting to the micro on the mainboard. What I dont know is what pin(s) on "PD" connector, between the 2 boards, has the Power On command from the micro to the PWR suppy board?? Want to make sure its not the PWR supply versus Mainboard problem? Any info is much appreciated. Thanks.

          Comment

          • freakaftr8
            Badcaps Legend
            • Oct 2012
            • 3743
            • USA

            #6
            Re: Sharp LC-70LE650 - Shaded on one side w/ line down middle

            Since rooms corrosion I would definitely say that your cheek on board probably is at fault as something else is making intermittent contact. When solder connections get corroded it can cause all sorts of problems. You may be out of the woods with a panel as if you had a perfect picture the panel is most likely okay
            Did I leave the soldering iron on?

            Comment

            Related Topics

            Collapse

            • SmartSarah
              Sharp LC70LE747 Flickering - darkening gradually to the right side
              by SmartSarah
              Dear,

              I can not pinpoint the following problem on my Sharp TV LC70LE747E.
              While the left side of the screen is not affected at all the right side of the screen gradually fades to a kind of dark. I can best describe this darkness like a totally worn out CRT display or a gamma correction totally out of range. This darkness flickers like a flame, a dark one tough.
              Sometimes when I restart the TV it disappears for a while.
              The problem worsened over time the last few months.

              I've replaced the t-con module without success. The problem remains.
              ...
              05-23-2022, 01:00 PM
            • Rozp
              70LE660U dark cloud or black screen with sound.
              by Rozp
              Hello Everyone,

              This is my first post so I will try to be as precise as possible without making this post too long winded. Unfortunately I don't have pictures of the original problem but I included images of the TV internals.

              I have a Sharp 70LE660U. The problem started a few months ago with the bottom row looking out of sync and was dark on the left side and then fading to transparent on the right side. Shortly after, a dark cloud appeared in the center of the screen. The dark cloud started small and shaded but the image was visible. It also affected the menu area....
              08-29-2023, 05:25 PM
            • flibidy
              Magnum IA.100 Amplifier Switches on, No Output, Possible Input Side fault?
              by flibidy
              I have here a Magnum IA.100 which belongs to my parents.



              The unit powers on & when the relay kicks in, you get a pop from the speakers (this might sound weird but is usual behavior for this amp). However, you get nothing coming through it from any of the inputs & no pops and crackls from any of the controls.


              Because of the sound from the speaker when the amp turns on I have assumed that the output section probably works but I could be wrong & I'm not sure how to test that side of things further.


              What Ive done........
              01-01-2025, 01:26 PM
            • Bdm634
              Sharp TV 2 5 code. Possible bad side panel
              by Bdm634
              Please help

              SHARP LC-70LE857U

              First it started with the tv working fine for about 20-30 minutes. Then it would start getting moving horizontal lines and extreme dimming on the one side. I did some research and it pointed me to a bad main board but also some people said bad power supply board. After the last test I did, the tv would no longer turn on and was giving the 2-5 code

              So I found a good deal on a power board and it came in today. I replaced the board. No luck. Still 2-5 code.

              Then I did some more research and found a test where I was...
              05-05-2020, 12:24 AM
            • bouny56
              Lenovo E15 Nm-c421 usb-c work only in one side
              by bouny56
              ​Hello

              Laptop E15 I5 10gen
              Mb nm-c421

              I have a problem with the usb-c power dc.
              The motherboard start only in one side of the usb-c

              Replace the usb-c port 2 times same problem

              With the usb-c meter, one side 20v ok, other side the usb-c meter don't come on

              Try to test the pin with the Mechanic Tail insertion tester and every pin are ok ?

              Can the pd controler be the fault ? Or something else maybe ?

              Thx

              ...
              02-11-2025, 03:15 AM
            • Loading...
            • No more items.
            Working...