Hitachi 50" Plasma Buffer board question

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • topfli8979
    Badcaps Veteran
    • Oct 2012
    • 311
    • USA

    #1

    Hitachi 50" Plasma Buffer board question

    Im going to attempt to repair this sdr d buffer off a Hitachi Plasma Im working. I have already verified the tv works with the board out of circuit. I am not finding and pin holes in any of the 8 ic's on the board. My question is how to I test which ic is bad? There is only 3 ribbon connections and 8 ics. I would understand there were 4 connections >2 ic's per connection.
    Attached Files
    Last edited by topfli8979; 06-15-2015, 06:08 PM.
  • chrismurphy
    Badcaps Veteran
    • May 2014
    • 251
    • australia

    #2
    Re: Hitachi 50" Plasma Buffer board question

    https://www.youtube.com/watch?v=51SZsfH60EY
    Use the same procedure as shown ,your board will be slightly different but the same principle applies

    Comment

    Related Topics

    Collapse

    • howardc64
      TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
      by howardc64
      All left and right refers to looking from rear of TV (or looking from front with TV upside down)
      • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
      • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
      ...
      07-24-2025, 05:17 PM
    • howardc64
      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
      by howardc64
      Problem

      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
      08-04-2024, 10:36 PM
    • Tynan Dill
      Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
      by Tynan Dill
      I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

      Upon bringing it home and plugging it up, it showed a standby light.

      I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

      The screen seems to blackout and stay black, but with a flashlight I can see the display.

      With my Playstation 4 connected via HDMI, and running a game I can hear sound.

      Assuming...
      11-22-2024, 01:46 PM
    • m1ch43lzm
      HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
      by m1ch43lzm
      Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
      Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
      05-12-2025, 08:37 PM
    • sotodefonk
      Help finding the correct model of a T-Con board on my Hitachi TV
      by sotodefonk
      Hi, I have a Hitachi tv model L47V651, there is no image, but sound and backlights turn on, so I believe the issue is the tcon board.

      I opened the tv to access the board and took the shared pictures of the T-Con board.

      I saw a video from shopjimmy on how to detect the model number on tcon boards, but this doesn't have a sticker like how that video showed all boards.

      I searched the P/N number and got results with the same marking name and P/N my board has but they list other specific tv models like Vizio and Philips brand but not Hitachi.

      Inspecting...
      06-28-2024, 04:39 PM
    • Loading...
    • No more items.
    Working...