LG 50PJ350 Mal Discharge

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Josh094
    Member
    • Jul 2013
    • 17
    • Australia
    #1

    LG 50PJ350 Mal Discharge

    Hi there guys, I've got an LG 50pj350 here with what looks like rather bad Mal discharge. Tv was working fine the night before, when turned on the next day the screen flickers bright white at start up then turns on as normal however there seems to bed severe mal discharge (sparkles everywhere).

    I read a thread here where someone had the same issue which was solved by replacing the Zsus board so I decided to wing it and replace the zsus however the issue remains. I've tested voltage test points on the power supply, ysus and zsus boards and all appear to read correctly (Va: 60v; Vs:208v; VSC:198v; vy:135v; VZB:100v). Unsure how to proceed from here, assuming something is wrong with YSUS board? However I don't know how to confirm this and they are rather pricey at about $125USD, there are repair kits available but they don't list which components are included.


    Thanks in Advance.
    Tags: None
    • tw2005
      Badcaps Legend
      • Oct 2011
      • 6458
      • Australia
      #2
      Re: LG 50PJ350 Mal Discharge

      I have a complete boardset for this model gathering dust from broken panel.

      Hard to say whether you may have bad buffers or there have been some LGs reported here with cracked solder on some of the inductor coils on the ysus (I think). Just not sure if this model or not.

      Pictures? Not greatly familiar with the LGs.

        Comment

        • Josh094
          Member
          • Jul 2013
          • 17
          • Australia
          #3
          Re: LG 50PJ350 Mal Discharge

          Hey mate, just took a few quick pictures, let me know if there's something in particular you need photos of. On the plus side I've managed to find a replacement board for about $40pp if it comes down to replacing it.

          http://i270.photobucket.com/albums/j...ps1bf09d80.jpg

          http://i270.photobucket.com/albums/j...psa57b7b37.jpg

          http://i270.photobucket.com/albums/j...ps94258d19.jpg

            Comment

            • tw2005
              Badcaps Legend
              • Oct 2011
              • 6458
              • Australia
              #4
              Re: LG 50PJ350 Mal Discharge

              Originally posted by Josh094
              Hey mate, just took a few quick pictures, let me know if there's something in particular you need photos of. On the plus side I've managed to find a replacement board for about $40pp if it comes down to replacing it.

              http://i270.photobucket.com/albums/j...ps1bf09d80.jpg

              http://i270.photobucket.com/albums/j...psa57b7b37.jpg

              http://i270.photobucket.com/albums/j...ps94258d19.jpg
              Hoping for a pic of the actual fault. looks ok in the only shot of the screen. Yeah $40 is a good price although rare to find much here for sale.

                Comment

                Previous template Next

                Related Topics

                Collapse
                • PlasMatt
                  LG 60PV450 Possible Bad YSUS Need help confirming Diagnosis
                  by PlasMatt
                  I have an LG plasma that after reading through a bunch of posts and doing some testing I believe has a bad YSUS board. The problem is that that doesn't make sense to me for some of the symptoms. The problem started yesterday. While watching a movie the TV just shut down like I pressed power. I have it hooked to a PC and use RS232 to turn it off and on so I thought maybe something had glitched there. I turned it back on and finished the movie with no problems. The same thing happened today so I checked logs to see if something in the control glitched and sent an off command but it didn't, After...
                  09-20-2025, 06:50 PM
                • Salvatore057
                  plasma TV Lg 42w451 - why is the zsus igbts damaged when the ysus is plugged?
                  by Salvatore057
                  Hi all,
                  I am trying to fix my plasma TV which is not powering on due to damaged IGBTs. I have changed two igbts and 2 IC drivers on the zsus and also two igbts on the ysus.
                  Now everytime I plugged the ZSUS and the YSUS boards to the power board, the two 30f124 IGBT on the ZSUS are damaged and the TV stays in standby mode. When I plug the ZSUS board alone the TV turns ON but I do not see pictures. When I plug the ZSUS board without the two 30f124 IGBTs and the YSUS board, the TV powers on with a picture.
                  I am lost, should I change the YSUS board? Is the YSUS board damaging...
                  04-29-2018, 01:29 PM
                • JDC
                  LG 60PB6650 - Bad ZSUS (3.8v to YSUS instead of 16v)?
                  by JDC
                  Make and Model: LG 60PB6650-UA
                  Issue: Turns on, no backlight, can hear static (no channel)

                  I've been repairing TVs for a couple years now. I know how to use a multimeter for the most part and know how to test most components for shorts.

                  The power board connects to the ZSUS and then connects to the YSUS. The ZSUS is where I believe the failure is because the 16v line is only 3.8V, even when I disconnect the ZSUS from the YSUS.

                  This particular model seems to have a common failure with its YSUS. My goal earlier was to prove the YSUS was bad so I could...
                  09-13-2018, 02:12 PM
                • zwarder
                  eax61319402 50PJ350 YSUS
                  by zwarder
                  Hi
                  Had shorted YSUS

                  Q24 RPJ63F3
                  C726 cap
                  Q11 K3667
                  R528 & R529 2.2 ohm

                  replaced all of these but still trips psu VS & VA are a bit low when ysus disconnected. IC301 does look a bit burnt however

                  ZSUS is also good as far as I can tell

                  Anyone could help me out on this one
                  10-23-2023, 08:11 AM
                • legg
                  LG 42PC3 buffer output doesn't follow YSUS
                  by legg
                  LG42PC3D -UD originally with green lamp but no display or audio.
                  Owner says was working, then went 'pop'.
                  All 5V caps bulging. replaced.
                  All PSU output voltages within spec but -Vy is low on YSUS.
                  One of three parallel fets between SUS_OUT and SUS_DN is zenering,
                  eventually shorts DG. Replaced all 3 - -Vy now OK.

                  Y scan buffer test point does not follow YSUS output below -50V

                  Note: This unit seems to expect YSUS output to park at -Vy in between
                  drive signal pattern periods. A replacement drive signal board confirms this....
                  11-18-2021, 11:49 AM
                • Loading...
                • No more items.
                Working...