LG PDP42X30201 Picture Problem.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • wadenvk
    Senior Member
    • Nov 2011
    • 55
    • United States

    #1

    LG PDP42X30201 Picture Problem.

    Just wondering if any one has any idea what could cause this. I replaced the y-main and buffer a while back, now it is doing this. it worked just fine for two months. then I started to see red sparkles then went to this.
    Attached Files

    if you find these attachements useful please consider making a small donation to the site

    Last edited by wadenvk; 04-18-2014, 11:16 AM.
  • tom66
    EVs Rule
    • Apr 2011
    • 32560
    • UK

    #2
    Re: LG PDP42X30201 Picture Problem.

    Z-sustain fault in my opinion.
    This is the Z-sustain: https://www.badcaps.net/forum/attach...7&d=1397841223

    Check the fuse on it is OK.
    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
    For service manual, schematic, boardview (board view), datasheet, cad - use our search.

    Comment

    • wadenvk
      Senior Member
      • Nov 2011
      • 55
      • United States

      #3
      Re: LG PDP42X30201 Picture Problem.

      Thats were I will start thank you. The fuse is good.

      Comment

      Related Topics

      Collapse

      • doorzon
        AOC AGON AG273QCG refresh problem picture shifts
        by doorzon
        Hi all,

        hopefully someone on this board has an idea on how to begin with troubleshooting this problem.

        The monitor AOC AGON AG273QCG (curved 27" QHD monitor) has problems refreshing every 1 to 2 seconds or so. A line appears in the middle of the screen and the lower half of the screen is shifted to the right.

        See attached picture.

        I am leaning towards an issue with bad soldering of the graphics chip, because the problem used to go away after some time (minutes) but now it is here to stay.
        However, this could also be related...
        08-12-2023, 02:36 AM
      • Tr0ll
        T-con suspect issue. Both ribbon cables no picture. One ribbon cable ok. (58pus8545)
        by Tr0ll
        Hi guys! I realized you have a lot of knowledge here so i am hoping you could point me in right direction with my odd issue.

        The Tv is a Philips 58PUS8545/12, it had no picture but working backlights.

        Original T-con:
        Opened the Tv and tested to unplug one ribbon cable at a time. With this test i could see that i got fine picture on both halves as long as there was only one ribbon cable connected, with two connected picture were gone.

        First replacement T-con:

        I thought it might be t-con and ordered new t-con from china(supposedly tested)...
        10-07-2023, 07:48 PM
      • retrorepair
        SONY KDL-40P3600 Picture Problem
        by retrorepair
        Hello gurus, hope you can assist me...

        I have a Sony KDL.40P3600, with an issue on the left side of the screen (pictures attached).

        I think the problem is the panel, but before send it to trash, i would like to get a second opinion.

        Thanks in advance.
        10-11-2024, 05:12 PM
      • KYBOSH
        Samsung UN55MU8000 - Backlight But No Picture Problem
        by KYBOSH
        Hello all

        I pick this up free as a repair project for the holidays.
        The original symptom was power cycling after 3-4 seconds with a single red light flash.

        To remedy this I went through and unplugged each component 1x1 and discovered that when the FFC cables were disconnected the backlights stayed on and the TV did not reboot.

        I tried remove one or the other to see which side of the display was causing the issue (expecting to see half a picture to show) but didn't see anything. But the boot loop only appears when the top FFC cable (right side...
        12-21-2022, 12:42 AM
      • Rusenga
        Samsung PS43E450A1R Picture Problem
        by Rusenga
        Hie techs, I have a samsung plasma TV which when plugged in shows a very dull reddish image. Tested some voltages and below is what I get:

        Note the green light on the tcon flashes every second.

        Power supply board:
        PS on 0v
        Stby 5v
        VS CON 1.72v
        VS ON 3.2v
        VS 208v
        VA. 57v

        X buffer :
        Svt vs 209v
        Svt xout>flactuating between 280 to 900v

        Y main board:
        Svt vs. 208v
        Svt ve. more than 1000v
        Svt yg c More than 1000v
        Svt yout flactuating between 400v and 1900v
        Svt...
        11-24-2023, 09:26 AM
      • Loading...
      • No more items.
      Working...