Is there any. post on a lg32le5300? I just pick up a set
and everything measured good except 24v. i only had 18
and everything measured good except 24v. i only had 18
-
-
Re: lg 32le5300 no power/back light
post some pictures then someone will help you more -
Re: lg 32le5300 no power/back light
Not sure how the pictures are gona look..but it s. worth a shotAttached FilesComment
-
-
Re: lg 32le5300 no power/back light
Voltage on power board
0 = nc
12.09 =12
12.09 =12
12.09 =12
0=G
0=G
3.47=3.5
3.47=3.5
0 =G
0 =G
18.24 =24v
3.27=pwr onComment
-
Re: lg 32le5300 no power/back light
The 2 nd from bottom reading is
18.42 v =20VComment
-
Re: lg 32le5300 no power/back light
Can the backlight be forced on with a jumper or not ?
First time seeing one set up like this with a backlight controlboard
mounted on the powersupply.Comment
-
Re: lg 32le5300 no power/back light
Im guessing the fault is in the led driver board..but not certianComment
-
Re: lg 32le5300 no power/back light
Ok i was able to. jump and make the back light come on.
Anyone have luck at finding the fault on the control board??Comment
-
Re: lg 32le5300 no power/back light
if you turn tv on in a dark room do you see a flash on screen ?Comment
-
Re: lg 32le5300 no power/back light
No..no flash . even tried to shine a flashlight...cant seea pic
but i was able to jumper the backlight on.Comment
-
Re: lg 32le5300 no power/back light
I did notice on voltage on power supply i don t have a
3.5 v reading. it is 0
AndComment
-
Re: lg 32le5300 no power/back light
I dont have a 3.5 v on back.light dim and a 3.5 both were
0 v. so wouldnt the power supply be the fault.Comment
-
Re: lg 32le5300 no power/back light
When the back light is forced on..i have all the correct voltages
so i will try to find a controll boardComment
-
Hi all,
TL;DR - this laptop is driving me nuts with the oddball power-related behaviors. Appreciate any insight you can provide!
I'm experiencing a power issue on an Asus Probook P5440UF-XB74. Although I've worked with electronics and computers for decades, this is my first attempt at getting into motherboard-level component troubleshooting. Any help the community can provide is greatly appreciated!
A few weeks ago I was using the laptop (on battery power) for a Zoom meeting. The battery was running very low (long meeting) but I wasn't worried about... -
hello, �� i have been sitting on some microsoft surface pro 4 tablets for a while now. i was originally tasked with replacing the battery in one of the tablets, and ended breaking the screen and logic board in the process. decided to buy another tablet with the same specs. got that screen off successfully of the second tablet. the logic board appeared good, but i guess i shorted something out in the installation process of the logic which i've read is a common issue if there is no barrier between the logic board and battery pins. all that said, i ate costs of the repair and have... -
This happened last Saturday and today I finally had time this morning before I went to work to replace two non brand capacitors
I will let you be the judge weather or not these are bad or not according to the blue ESR meter that I am using
I am comparing them to a brand new one that I installed
The display came back on and the programming was not lost which I was surprised by I would have thought that when the display went blank that so did the memory as well
I going to let it run for several days before I remount back on the wall next to the... -
Hi there,
I've got a 39" LG 39LN540V that's just spontaneously stopped working! The symptoms are - when I plug it in, the red light will flash on twice, then go out, there's no visible picture, and I couldn't see anything using a torch on the panel either. If I press the power button (either remote or on TV), the red light comes on continuously. If I press power again, the red light flashes twice.
The TV is using a power board EAX64905301. I've attached a diagram of the power output, I've tested the voltages with a multimeter and I'm getting the following:
... -
I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump
One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
Comment