Insignia NS-P501Q-10A

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • cesspool72
    New Member
    • Jul 2013
    • 4
    • usa
    #1

    Insignia NS-P501Q-10A

    Have a Insignia NS-P501Q-10A that will not power up,inside it has Samsung parts.Tried some suggestions off other posts with no luck.
    Attached Files

    if you find these attachements useful please consider making a small donation to the site

    Tags: None
    • tom66
      EVs Rule
      • Apr 2011
      • 32560
      • UK
      #2
      Re: Insignia NS-P501Q-10A

      Have you checked power supply voltages? Noted any relay clicks or other sounds?
      Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
      For service manual, schematic, boardview (board view), datasheet, cad - use our search.

        Comment

        • cesspool72
          New Member
          • Jul 2013
          • 4
          • usa
          #3
          Re: Insignia NS-P501Q-10A

          repair shop said was a bad y sustain board...which one is that? not an electronics guru here...thanks in advance

            Comment

            • tom66
              EVs Rule
              • Apr 2011
              • 32560
              • UK
              #4
              Re: Insignia NS-P501Q-10A

              Y-sustain = Y-main... large left hand board.
              Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
              For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                Comment

                Previous template Next

                Related Topics

                Collapse
                • cajoeg
                  Insignia NS-LCD019-09 issue: Power light turns blue for 3 seconds, the flashes red before going solid read again
                  by cajoeg
                  Hello, I'm new to the group and to trying to repair a LCD TV. During the past few years, I've been collecting/repairing/restoring vintage personal computers (Commodore, Apple II, Atari, TRS-80, Texas Instruments, and Timex Sinclair). This has been my retirement hobby. Now I've gotten interested in trying to repair a LCD TV that I have and used regularly when working on vintage computers.

                  The LCD I'm working on is a Insignia NS-LCD019. I've downloaded the service manual that I could find, but it must be a different revision since not too many items in the service manual match the TV...
                  02-10-2025, 04:01 PM
                • valvashon
                  Insignia NS-LCD19-09 (third and final post, hopefully!)
                  by valvashon
                  I have been going round and round with this one for a couple of years. It's a 16x10 display that allows you to size your OTA picture correctly to 16x9 and that makes it kind of cool so I really want to keep it on my OTA monitoring wall. Accidentially let a screw roll under the powered power supply board and ended up replacing the MOSFET drivers for the inverters, then one of the Schottky rectifiers for one of the supplies, then the PS caps becuase I fired the parts cannon at it one day.

                  Problem was no cold startup; it would only startup when you applied a heat gun to the board....
                  10-22-2025, 12:33 PM
                • valvashon
                  Insignia NS-LCD19-09 no standby LED; (new problem)
                  by valvashon
                  Having a new problem with the 19" Insignia that I modified with one of my automatic turn on circuits. That is now completely disconnected so that is not the issue. I was doing some modifications on that circuitry and managed to short something out on the underside of the power board.
                  Actually found and bought the service manual (who knew it was even available?!) which brought me to the High Voltage Startup Circuit controller chip.
                  Looking up that chip number- LD7575APS brought me to the attached datasheet. I have marked my voltage readings on the schematic sheet (open in new...
                  08-30-2023, 10:41 AM
                • tbsmith
                  Insignia NS-50F301NA24 No standby power, no +Va, Vm, +Vl etc.
                  by tbsmith
                  There is voltage on the bridge rectifier and main caps (163V). Fuses all check good. One of the smaller electrolytic caps (C9112 which is 50V, 100uF) looked bloated, it measured 60uF with one tester, and defective with another. I replaced it temporarily with same uF rating, higher voltage since I don't have the exact one. I also found that one of the switching mosfets (for lower voltage DC supply I think) was shorted. It is a 50R800CE which I didn't have, but had something with the same voltage and current rating and a similar Rds. None of these fixes helped. I'm out of ideas. Any suggestions...
                  1 Photo
                  08-11-2025, 06:15 PM
                • howardc64
                  Insignia NS-43D420NA20 backlight on no display - LCD panel burn failure
                  by howardc64
                  Eventually discovered a burn mark near lower corner of LCD. Here is a summary
                  • Backlight on, no image
                  • Disconnect right buffer board (view from front), left side display comes on
                  • Masked off pin 7+8 (both ~12,5v on both left and right buffer board) from t-con to right buffer board (view from front) display works but have some lines
                  • Buffer board is pretty simple
                  Removed the front bezel to examine edge of the glass. Found burn mark on lower right (view from front). Plastic bezel covering the burn mark region shows heat signature on the inside surface facing the LCD panel. Last 2 pics. Bright...
                  07-11-2025, 04:04 PM
                • Loading...
                • No more items.
                Working...