mlk386x power supply and cap data sheets.

Bangulo

Member

Join Date: Jun 2013

Posts: 21

Country: USA
#1

mlk386x power supply and cap data sheets.

06-18-2013, 07:12 PM

So i have this MLK386x Power supply that has busted caps all around. My question is when looking at the data to order replacement caps. how do you know what ones are rated for 105 C

Two of these huge samxon 100uf 450v or blown from the back. these caps are pretty huge. Would this be sufficient?

https://cdn.badcaps-static.com/pdfs/...693d4ab034.pdf
Tags: None
Bangulo

Member

Join Date: Jun 2013

Posts: 21

Country: USA
#2

06-18-2013, 07:14 PM

Re: mlk386x power supply and cap data sheets.

Sorry for the double post you can delete this thread. it told me to log in when i hit post then i logged in and now it double posted.
Comment

Previous template Next

Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?

by Tynan Dill

I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

Upon bringing it home and plugging it up, it showed a standby light.

I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

The screen seems to blackout and stay black, but with a flashlight I can see the display.

With my Playstation 4 connected via HDMI, and running a game I can hear sound.

Assuming...

7 Photos
- Channel: Troubleshooting TVs and Video Sources
11-22-2024, 01:46 PM
Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply

by sam_sam_sam

I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
- Channel: General Electronics Technical Discussion
03-31-2024, 02:12 PM
Modification to a ZD-987 desoldering/soldering station using a external switching power supply

by sam_sam_sam

I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
- Channel: General Electronics Technical Discussion
07-01-2024, 06:34 AM
Russound CA4 Power Supply Repair

by CMCM

Hello Everybody,

Trying to repair a power supply from a Russound CA4 Multizone Controller (picture attached)

Russound no longer supports it but were kind enough to provide a schematic of the power supply (pdf attached).

The outputs marked 12v and 20v are all measuring only 1v.

The board is clicking, which I think means it is in something called hiccup mode when the flyback transformers switches because of an internal problem or something else on the board Overloading it.

The capacitors physically look clean (no bludgesor leaks) and...
- Channel: Troubleshooting Power Supplies and Power Supply Design
07-03-2025, 01:12 PM
Mid 2014 A1398 MacBookPro,Is it feasible to remove the battery from the MBP and connect it to an external power supply?

by Gust zhang

I have a 15 - inch Retina MacBook Pro from the mid - 2014 model. Here is the link: https://www.badcaps.net/forum/showth...light=820-3662 . The battery broke some time ago. After I removed the battery and plugged in the original power adapter, the MBP could boot up normally. However, when I checked with IntelPowerGadget, I found that the CPU speed was limited to 0.8 GHz, and it ran very slowly. Later, I found a solution on GitHub. There is an open - source project called cputune that can set the CPU running speed. So I can now run the MBP at full speed. But another problem...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
02-16-2025, 08:39 AM
Loading...
No more items.

mlk386x power supply and cap data sheets.

mlk386x power supply and cap data sheets.

Comment

Related Topics