First plasma, LG 42PC5D. Sound but no picture. Help me make sense of this.

[mattpd]

Re: First plasma, LG 42PC5D. Sound but no picture. Help me make sense of this.

What is the board number on your ysus? IPMs are expensive and a PAIN to delsolder so if you can find a replacement ysus for a reasonable price, i would buy it.

And yes, you wont be able to unhook one buffer at a time because they appear to be all on one board.

[tom66]

Re: First plasma, LG 42PC5D. Sound but no picture. Help me make sense of this.

The IPM failures, and the sparklies issue, are two reasons I stay away from these sets.

Note I have never heard of a bad Y-sustain killing an LG buffer board, though I wouldn't rule out the possibility.

[rayrod81]

Re: First plasma, LG 42PC5D. Sound but no picture. Help me make sense of this.

It is possible that IPM has failed open circuit and it will not blow the fuse. This IPM failure is by far the most common problem on these sets. It is possible that the caps are causing the no picture condition as they control the low voltages going the main board but if that does not fix it then it Y-sus IPM is probably the culprit. The IPM can be found for $20-$30 if you use the Sanyo STK795-820(or 821) or $40-$50 if you use the LG YPPD-xxxx module. You will need to know which chip is on the board now as the STK795-xxx chip may not be compatible with all versions.

Be aware that unless you have a very high temp soldering iron and take your time (it can take a good 30 minutes or more to remove the chip) then you will be very likely to damage the board. Also, even after the TV is fixed you may notice red, blue, and green sparkles that cannot be fixed without a special jig to update the firmware on the Logic Board.

[johnboy1313]

Re: First plasma, LG 42PC5D. Sound but no picture. Help me make sense of this.

Just getting ready to head out for the day. I've read that you can test the buffers by disconnecting one or the other to see if half of the screen lights up. It looks like that is not possible on this set. Am I correct?




Tom, I checked the fuses, they all seem to be OK.

[tom66]

Re: First plasma, LG 42PC5D. Sound but no picture. Help me make sense of this.

Those caps go bad because they are Samwha. Since there are so many the TV only starts having problems a few months from now.

The long board along the bottom of the plasma panel is the X drive distribution board.

The board underneath the main board is the control board.

Check the Y-sus fuses.

[mattpd]

Re: First plasma, LG 42PC5D. Sound but no picture. Help me make sense of this.

Your upper and lower buffer are on the far left side of the tv if you are facing the back (skinny vertical board). Looks to be one piece on this tv. You ysus board is the one with big heat sinks connected into the right side of the buffer. Your xsus (or zsus, I forget what lg calls it) looks similar to your ysus and is on the far right of the tv


I fixed almost the same tv with the same problem with a new ysus board. I think the IPM failed, but I didn't bother to check because a replacement board was cheap. Those caps might have something to do with the ysus. Maybe replacing them will provide proper voltage to ysus and bring the tv back the life. If not, time to check voltages

[johnboy1313]

Re: First plasma, LG 42PC5D. Sound but no picture. Help me make sense of this.

So it seems that the "one" long board on the bottom is actually two boards. Are those the upper and lower buffers?

[johnboy1313]

I just want to post these pics to ID what's what inside this thing. I've read a bunch of posts. I suspect the Y-Sus or one or both of the buffers, but I'm not really sure about everything I'm looking at.

To start, power supply. Several bad caps. I'll replace them but I'm not expecting it to fix the problem.



Main board


Z-Sus and label



Y-Sus and label



Y-Driver?? and label



I don't know what this board is. I thought I got a pic of this board. It runs along the bottom of the panel.



I don't know what this little guy is peeking out from behind the right side of the main board. (last two pics should have been rotated 90 degrees)



I'm working out of the office tomorrow so I won't be around much to answer question. I probed six fuses in all. Two glass fuses on the Y-Sus, two glass fuses on the Z-Sus, one surface mount fuse on the Z-Sus, and one glass fuse on the power supply. They all test good. That's as far as I got. It's late and I'm going to bed. I'll get back to you tomorrow afternoon sometime.