Magnavox LCD TV power fluctuation

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • dman623
    Member
    • Oct 2012
    • 12
    • USA
    #21
    Re: Magnavox LCD TV power fluctuation

    I replaced 3 x 1000uf 35v from radioshack

    An additional bulging cap is 220uf 35v

    I also have:

    2 x 33uf 50v

    1 x 1000uf 16v

      Comment

      • Mr Bill
        Badcaps Veteran
        • Nov 2011
        • 648
        • USA
        #22
        Re: Magnavox LCD TV power fluctuation

        ok, These are all from Digikey. I am somewhat guessing at sizes but i have a few power supplies in my basement that are sorta close to your design. Check the dimensions (diameter & height) before ordering to make sure it's all gonna fit. I've made the mistake a few times getting a cap that was too tall but i believe your tv doesn't have a cage that goes over it so it shouldn't be an issue.

        1000uf 35v
        http://www.digikey.com/scripts/DkSea...=0&y=0&cur=USD
        1000uf 16v
        http://www.digikey.com/scripts/DkSea...7&y=19&cur=USD
        220uf 35v
        http://www.digikey.com/scripts/DkSea...7&y=20&cur=USD
        33uf 50v
        http://www.digikey.com/scripts/DkSea...9&y=20&cur=USD

          Comment

          • dman623
            Member
            • Oct 2012
            • 12
            • USA
            #23
            Re: Magnavox LCD TV power fluctuation

            Thanks so much for your help. I'll post back here when I've replaced those.
            Last edited by dman623; 10-11-2012, 08:21 PM.

              Comment

              • dman623
                Member
                • Oct 2012
                • 12
                • USA
                #24
                Re: Magnavox LCD TV power fluctuation

                I installed the new caps and it worked like a charm. Thanks so much for your help.

                  Comment

                  Previous 1 2 template Next

                  Related Topics

                  Collapse
                  • PantherDave
                    Microsoft Surface Pro (5th gen) model 1796 - no power
                    by PantherDave
                    Hi all!

                    I'm trying to troubleshoot a Microsoft Surface Pro (5th gen) model 1796 that won't power on. Motherboard model is M1007506-015. My priority is retrieving data, but the SSD is integrated so it looks like if I can't repair it it'll need to go to a data recovery company. I've done a little basic board repair before, but nothing this advanced until now. So please forgive my ignorance in advance. 😅

                    I found the boardview for this laptop in the forums here, and am able to open it on my PC with FlexBV.
                    https://www.badcaps.net/forum/troubl...-hardware-devi...
                    05-29-2024, 02:01 PM
                  • ipatch
                    troubleshooting microsoft surface pro 4 no power no led charge light
                    by ipatch
                    hello, �� i have been sitting on some microsoft surface pro 4 tablets for a while now. i was originally tasked with replacing the battery in one of the tablets, and ended breaking the screen and logic board in the process. decided to buy another tablet with the same specs. got that screen off successfully of the second tablet. the logic board appeared good, but i guess i shorted something out in the installation process of the logic which i've read is a common issue if there is no barrier between the logic board and battery pins. all that said, i ate costs of the repair and have...
                    10-05-2023, 11:59 AM
                  • russpall
                    LG 39ln540v - red light flashes twice, no power to LED driver?
                    by russpall
                    Hi there,

                    I've got a 39" LG 39LN540V that's just spontaneously stopped working! The symptoms are - when I plug it in, the red light will flash on twice, then go out, there's no visible picture, and I couldn't see anything using a torch on the panel either. If I press the power button (either remote or on TV), the red light comes on continuously. If I press power again, the red light flashes twice.

                    The TV is using a power board EAX64905301. I've attached a diagram of the power output, I've tested the voltages with a multimeter and I'm getting the following:
                    ...
                    Pin out and expected voltages
                    2 Photos
                    08-27-2024, 01:07 PM
                  • sam_sam_sam
                    Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
                    by sam_sam_sam
                    I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

                    One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
                    03-31-2024, 02:12 PM
                  • sam_sam_sam
                    Laptop computer that went completely dead no boot no power light no hard drive light
                    by sam_sam_sam
                    See pictures for type of laptop computer

                    I checked switching power supply brick 19.2 volts multi meter only

                    No booting without switching power supply connected

                    Checked switching power supply with an (28 volt ) incandescent light bulb it lights then hooked up the switching power supply again now the laptop and boots like normal

                    What the heck is going on here...
                    04-04-2025, 04:58 AM
                  • Loading...
                  • No more items.
                  Working...