Goodmans LD3265 - Powers on fine, but stuck with blinking LED when switched to s/by

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • tom66
    EVs Rule
    • Apr 2011
    • 32560
    • UK
    #1

    Goodmans LD3265 - Powers on fine, but stuck with blinking LED when switched to s/by

    After fixing this TV with a replacement power supply, this TV powers on fine and gives a good picture. However, when the standby button on the remote is pressed, the TV will shut down (as expected), but the LED then starts blinking. The LED keeps blinking like it's a fault code. You then can't turn the TV on again, until you unplug it.

    It's a Vestel chassis. 17MB22 I think.

    Any idea what might cause this?
    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
    For service manual, schematic, boardview (board view), datasheet, cad - use our search.
    Tags: None
    • tom66
      EVs Rule
      • Apr 2011
      • 32560
      • UK
      #2
      Re: Goodmans LD3265 - Powers on fine, but stuck with blinking LED when switched to s/

      Fixed it . Turned out the Freeview module cable was loose. Doh!
      Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
      For service manual, schematic, boardview (board view), datasheet, cad - use our search.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • Stunt
          Hp Laptop Stuck on Hp protected by hp sure start screen
          by Stunt
          Hi guys i've got an Hp laptop Zbook 17 g5 Stuck on Hp protected by hp sure start screen.
          I have tried almost every bios available on various platforms about this laptop but the problem is still the same.
          I even successfully build my own bios using the one from the Hp website but the problem the laptop still getting stuck there.
          Even if i try to press Esc key nothing happens. I tried f10 it doesn't go to bios still stuck there i just saw entering setup menu on the bottom left corner of the
          screen that's it and stuck there. I left it until the following day and i still...
          09-02-2025, 01:51 PM
        • Exim
          ASRock N100M, no picture no boot, but semi-alive
          by Exim
          Hi guys,
          I managed to semi-kill an ASRock N100M board after updating Bios from 1.10 to 2.01. It's a zombie now, dead, but not dead.

          ASRock N100M special features:
          - CPU soldered to board, small Intel 12th gen
          - iGPU
          - four POST LEDs

          Problem after updating Bios to 2.01 using the in-Bios update tool: no picture, no boot.
          I am not sure anymore if it booted at least once successfully after updating the bios to 2.01, maybe not, I can't remember. I think it did not.

          Symptoms:
          - no picture/signal on any of the display connectors,...
          board
          2 Photos
          04-01-2025, 02:36 PM
        • horus100
          Toshiba Z30-A-197 toshiba switched off and 2 blinking leds
          by horus100
          Hi, I've a problem with my laptop toshiba Z30: do not swith on and thare are 2 blink leds, white and yellow, blinking 2 times each one. I have disconnected the battery, CMOS battery, and reset bios but no effect, the laptop remain still switched off. Do you have any suggestion? Thak you!
          12-19-2022, 01:25 AM
        • Umadbro
          Dell Inspiron 3481 (EDI72 LA-G714P) Powers with charger blinking code
          by Umadbro
          Hi, I've been given this laptop which upon plugging the charger it produces a blinking code, and it goes as follows:

          "3 AMBER, 5 WHITE"

          Pressing the Power Button, the machine seems to power up, as the fan spins (at a normal rate), but after a few seconds the power cuts off, and the cycle repeats.


          Searching on Google for the blinking code for this device doesn't return any valuable information. The code is not listed on the service manual. However, I found out that for others or similar models "3 AMBER, 5 WHITE" blinking code...
          01-18-2022, 06:38 AM
        • stormanimal83
          Gigabyte B450 Aorus Pro stuck at VGA LED, burning hot LED Controller MCU 1 under PCI slot...
          by stormanimal83
          Hey....

          Board as written in description was stuck at VGA LED. common Problem wit these type of bords.... tried all the "standard stuff" like resettin... reseatin.... found out the LED Controller MCU1 = IT8295FN-56A geting burning hot under the last PCI Slot.. now i desoldered it cause there were only 18 ohms at the caps arround.... another aorus x470 in working condition with similar part and nearly same layout had arround 280 ohms...

          my question is: why doesnt the board start know without this chip.... worked myself through the boardview but i can´t understand...
          01-18-2024, 02:15 PM
        • Loading...
        • No more items.
        Working...