Goodmans LD3265 - Powers on fine, but stuck with blinking LED when switched to s/by

tom66

EVs Rule

Join Date: Apr 2011

Posts: 32560

Country: UK
#1

Goodmans LD3265 - Powers on fine, but stuck with blinking LED when switched to s/by

11-13-2011, 04:09 AM

After fixing this TV with a replacement power supply, this TV powers on fine and gives a good picture. However, when the standby button on the remote is pressed, the TV will shut down (as expected), but the LED then starts blinking. The LED keeps blinking like it's a fault code. You then can't turn the TV on again, until you unplug it.

It's a Vestel chassis. 17MB22 I think.

Any idea what might cause this?

Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.
Tags: None
tom66

EVs Rule

Join Date: Apr 2011

Posts: 32560

Country: UK
#2

12-07-2011, 03:44 AM

Re: Goodmans LD3265 - Powers on fine, but stuck with blinking LED when switched to s/

Fixed it . Turned out the Freeview module cable was loose. Doh!

Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.
Comment

Previous template Next

ASRock N100M, no picture no boot, but semi-alive

by Exim

Hi guys,
I managed to semi-kill an ASRock N100M board after updating Bios from 1.10 to 2.01. It's a zombie now, dead, but not dead.

ASRock N100M special features:
- CPU soldered to board, small Intel 12th gen
- iGPU
- four POST LEDs

Problem after updating Bios to 2.01 using the in-Bios update tool: no picture, no boot.
I am not sure anymore if it booted at least once successfully after updating the bios to 2.01, maybe not, I can't remember. I think it did not.

Symptoms:
- no picture/signal on any of the display connectors,...

2 Photos
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
04-01-2025, 02:36 PM
Toshiba Z30-A-197 toshiba switched off and 2 blinking leds

by horus100

Hi, I've a problem with my laptop toshiba Z30: do not swith on and thare are 2 blink leds, white and yellow, blinking 2 times each one. I have disconnected the battery, CMOS battery, and reset bios but no effect, the laptop remain still switched off. Do you have any suggestion? Thak you!
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
12-19-2022, 01:25 AM
Dell Inspiron 3481 (EDI72 LA-G714P) Powers with charger blinking code

by Umadbro

Hi, I've been given this laptop which upon plugging the charger it produces a blinking code, and it goes as follows:

"3 AMBER, 5 WHITE"

Pressing the Power Button, the machine seems to power up, as the fan spins (at a normal rate), but after a few seconds the power cuts off, and the cycle repeats.

Searching on Google for the blinking code for this device doesn't return any valuable information. The code is not listed on the service manual. However, I found out that for others or similar models "3 AMBER, 5 WHITE" blinking code...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
01-18-2022, 06:38 AM
Gigabyte B450 Aorus Pro stuck at VGA LED, burning hot LED Controller MCU 1 under PCI slot...

by stormanimal83

Hey....

Board as written in description was stuck at VGA LED. common Problem wit these type of bords.... tried all the "standard stuff" like resettin... reseatin.... found out the LED Controller MCU1 = IT8295FN-56A geting burning hot under the last PCI Slot.. now i desoldered it cause there were only 18 ohms at the caps arround.... another aorus x470 in working condition with similar part and nearly same layout had arround 280 ohms...

my question is: why doesnt the board start know without this chip.... worked myself through the boardview but i can´t understand...
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
01-18-2024, 02:15 PM
Sony kdl 40p5500 red light keeps blinking 3 times

by YasaCh

Hello...
my tv almost 2 years not powerd on and when i turned it on nothing happened and only 3 red light keeps blinking
i opened the back cover no sign of damage on the powery suply or motherboard
when i plug in the power i hear the reley sound like tik first and another tik..after that only red keep blinking..
another thing is even after i unplugged the power, The tv keeps red blinking 3 times for 2 almost 2 munites

2 Photos
- Channel: Troubleshooting TVs and Video Sources
Yesterday, 11:53 AM
Loading...
No more items.

Goodmans LD3265 - Powers on fine, but stuck with blinking LED when switched to s/by

Goodmans LD3265 - Powers on fine, but stuck with blinking LED when switched to s/by

Comment

Related Topics