RCA L26HD35D Pulsating screen/ t control?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • billansor
    Senior Member
    • Apr 2011
    • 85

    #1

    RCA L26HD35D Pulsating screen/ t control?

    Hi

    I had posted this earlier for a schematic and still have not been able to track this down..

    So went to try to figure this out...

    The set has a thumping and pulsating screen... Sooooo tried voltage measurements on the power supply and no shifting of voltages to account for the thumping and pulsating.

    I started to disconnect modules .... I disconnected the inverter and still thumping.. Disconnected the panel connection and the thumping went away... reconnected the inverter and the back light came up.... no pulsating and no thumping from the speakers..

    This set does not have a t control as such... The main board is a partial t control or am I wrong on that??

    This set is a bear to work in as it almost has to be together.... I had to make some adaptations to be able to work it split apart, but do not have room to turn the main and power supply module over..

    Thank you for your time!!

    Bill
    Attached Files
    Last edited by billansor; 10-24-2011, 03:00 PM.

Related Topics

Collapse

  • Ryan.man
    Macbook 2017 with touchbar (A1706) won't turn on after removing the screen
    by Ryan.man
    Hello everybody! Posting this in hopes somebody has some expertise that leads to a clear path of troubleshooting that saves me a lot of time!

    My macbook has the flex cable problem, the one that prevents the screen turning on. Ive been dealing with this for the last 3 years. Last year it went dead and I managed to fix it following youtube tutorials. But my fix wasnt the best, the problem returned a month later. This week, it went dead again. I again tried to fix it.

    This time the original cable broke too close to the screen, it can't be fixed without tearing the screen...
    02-04-2025, 12:23 PM
  • smic717394
    iphone XS turns off when press on screen.
    by smic717394
    Hi,

    I have a iphone XS that came in for a screen replacement, the screen was badly cracked, and inside missing scues, on the back of the screen still the blue protector, the screen was a LCD. So we replaced the screen and all good, installed the screen and we noticed that pressing the screen with a bit of force but not excessive, the phone dies. After plugging the charger it turns back on, but again if you press it it dies. I open the phone again, and I can't see anything major, with the phone open, if I press on the logic board, battery, charging board, or even putting pressure on...
    07-25-2024, 10:16 AM
  • Chrissygizmo
    Samsung UE55JU6800K half screen dark
    by Chrissygizmo
    Hello everyone, I’ve just been given a Samsung UE55JU6800K smart tv as it had white spots on the screen due to the led lenses falling off. After refitting them & putting the tv back together I thought it was a nice easy fix for a free bedroom tv , then I tried it before screwing the back into place. I realised that the right side of the screen was darker than the other side, I removed the screen again as I thought the backlights had failed but they are fine.
    I put the screen back in place & turned it back on . The screen seemed to be ok again but different screens on the same...
    02-10-2025, 12:33 AM
  • ipatch
    ipad pro 9.7" blew a SMD component while replacing the screen 🤦‍♂️
    by ipatch
    i have an ipad pro 9.7" (1st gen) A1674 where i replaced the screen, but never attached the screen to the frame/chassis (glued down) due to the ipad being previously dropped so the new screen would never fit in the frame properly. so i need flex/bend the chassis to eventually fix the new screen in properly. so i temporarily just applied blue tape around the edges of the screen to keep it in place. when watching videos with the ipad the screen started flicker, so i though maybe the new quasi cheap amz screen i purchased was going out. so i disconnected then reconnected with power still on,...
    08-24-2024, 02:36 PM
  • FreakyMex
    Trouble to identify part (Lunii screen) for replacement
    by FreakyMex
    Hello guys. I'm a complete noob in electronics. I'd like to repair my child Lunii's (a "story box"), basically an audio player that allows the childs to choose between several options the places, characters, objects of the story, and then play a story according to the choice of the child. There is a screen that display the selected option before each choice. The Lunii fell and the screen is now broken.
    I'd like to repair it (probably just have to change the part, because the lunii still works perfectly fine) but I can't manage to identify the part/order it online. Do you have any...
    02-17-2025, 01:16 AM
  • Loading...
  • No more items.
Working...