Dvr 4 output

Collapse
X
Collapse
+ More Options
Posts
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • quackeruk
    New Member
    • Apr 2010
    • 9
    #1

    Dvr 4 output

    Good eve friends, I have an unbranded four camera dvr, with hard drive,
    first off the psu burnt out, on further inspection a chip was found blown to pieces, the nearest thing i can find on the net is a firm called kylink, i need to find out what the chip is. U12. I will put photo on line tomorrow.

    If any can help with any info I would be very happy,

    rgds
    Tags: None
    • tom66
      EVs Rule
      • Apr 2011
      • 32560
      • UK
      #2
      Re: Dvr 4 output

      A photo will be essential, but you can help out by telling us what the reference number next to it is. It will be something like "U13" or "IC19" or "Q355", something like that...
      Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
      For service manual, schematic, boardview (board view), datasheet, cad - use our search.

        Comment

        • Dgtech
          E. Technician
          • Apr 2009
          • 1462
          • Steeler
          #3
          Re: Dvr 4 output

          You said unbranded but there's got to be a model number for the set or something. How about a board number?
          The strong-minded rise to the challenge of their goals,the weak-minded BECOME HATERS

            Comment

            Previous template Next

            Related Topics

            Collapse
            • FrancescoV
              Onkyo HT-R390 no sound output, video output ok
              by FrancescoV
              Good morning everyone,
              I'm trying to repair an onkyo ht-r390 that has no sound output, despite the volume being at maximum, the rest seems to work; the video output signal (coming from an hdmi input) is present, but the audio is absent. Similar situation if I send an audio signal from any input I have no output.

              The firmware reported is the following:
              M:1.00/11107BLP
              D:?.??/????????
              O:1.00/11107AL

              The DSP firmware given the question marks seems corrupt.

              On the BCHDM-0678 - 25140678 - QPWBCHDM0678A0 board the chip that usually seems...
              05-11-2025, 02:59 AM
            • sam_sam_sam
              NTE Electronics “NTE5251K” Zener Diode 9.1V @ 50W Do-5.5% Want to build a 9.1 output from a 9.6 lipo4 battery pack
              by sam_sam_sam
              I have bought this Zener Diode for this project what size and wattage resistor value do I need to use to get near 50 watt output
              I bought this from an eBay seller but unfortunately they only had one

              I bought three from Vetco Electronics these are Sylvania ECG5185A 9.1@10w A to Stud what size and watt resistor do I need to use to get near 10 watt output
              I bought three of from them to also make battery packs with this output power limit in mind

              I want to use this battery pack and turn it into a 9.1 output battery pack output to eliminate using 9 volt battery...
              04-23-2025, 05:50 AM
            • momaka
              Corsair CX750M [Model 75-002019] - burned output toroid inductor
              by momaka
              Looks like I may need a little help from the PSU experts (or anyone really! ) I have a Corsair CX750M (Model 75-002019) that I picked up for free about 4 years ago. This is the PSU:



              So here’s what’s strange about this one: it appears to work normally (normal output voltages) and any PC is stable with it. However, after a while (typically 10-20 minutes, but time can vary depending on the load), there is a sweetish smell of burned magnet wire insulation emanating from the PSU. Upon opening the PSU after this happened (many times), I was able to confirm...
              09-19-2021, 08:44 PM
            • CoppellTVRepair
              Troubleshooting PFC with SPC1012T not raising output
              by CoppellTVRepair
              It has been a long while since I posted here to ask anything....hope you can help.

              I have this Samsung power supply that uses SPC1012T as driver for the PFC and it's giving me a problem that I can't narrow down though I've troubleshooted and fixed hundreds of boards similar circuits.

              I am attaching a schematic from a different Samsung board, but the topography is very very similar if not 100% the same and it uses SPC1012T, which BTW is a pinout match to UCC28063 for which there's plenty of information. I haven't confirmed they are functional equivalents, but I strongly...
              03-09-2025, 10:38 PM
            • flibidy
              Magnum IA.100 Amplifier Switches on, No Output, Possible Input Side fault?
              by flibidy
              I have here a Magnum IA.100 which belongs to my parents.



              The unit powers on & when the relay kicks in, you get a pop from the speakers (this might sound weird but is usual behavior for this amp). However, you get nothing coming through it from any of the inputs & no pops and crackls from any of the controls.


              Because of the sound from the speaker when the amp turns on I have assumed that the output section probably works but I could be wrong & I'm not sure how to test that side of things further.


              What Ive done........
              Magnum IA.100 Front
              8 Photos
              01-01-2025, 01:26 PM
            • Loading...
            • No more items.
            Working...