Un55h6350afxza

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • jkb242
    replied
    Re: UN556350AFAZA

    Update following system board replacement

    Unfortunately no change but pursuing a couple follow on checks and requesting clarification on an earlier diagnostic testing.

    -When removing one of display ribbon connections at the T-Con board with the power board connected to the system board, then applying AC power, I reported seeing the backlights turn on while viewing the rear panel and seeing a very dim backlight, across the screen, barely noticeable viewing the front of the display. Should the backlights be fully turned on at this point? The same question also applies to the other test with the power board disconnected from the system board. Why do the backlights turn on with either one of the T-Con to display ribbons connected but not both? Also, should there not be a viewable message of “no input” displayed on at least 1/2 the screen? Assuming there were video sources connected to the system board?

    With the replacement system board installed and both boards connected normally, I also noted when AC power is applied, the standby LED blinks 6 times and extinguishes. Could this be due to the EEPROM having lost its programming or possibly being corrupt?

    Much thanks for additional input.

    Leave a comment:


  • jkb242
    replied
    Re: Un55h6350afxza

    Lotas mention this site which I took as a reference location to see the board to which he referred in his explanation, you followed his post with a link containing the same vendor's name which I mistakenly took to appear as a recommendation. You obviously knew this vendor was not one to be recommended since you knew what complaints had been written.

    Shame on me for not “catching” that link was to a warning but with everything in mind, you were careless not make this clear the link was to a warning. I'm not inferring you did this with intent to mislead but the seeing link alone was certainly not sufficient.

    I admit I should have checked out the link to see it wasn't an endorsement. That was clearly my mistake. I have kept my comments direct and professional without personal insult. I don't believe that's too much to ask of you. Please see attached.




    Attached Files

    Leave a comment:


  • nomoresonys
    replied
    Re: Un55h6350afxza

    What are you smoking PAL? I didn't post a link to that site, Lotus did, before you start running your BIG MOUTH, try reading something when posted.

    Leave a comment:


  • jkb242
    replied
    Re: Un55h6350afxza

    Originally posted by jkb242
    Great info thanks. I suppose the board number you recommended was one that is more universal for this series and will accept the appropriate programming or paring with the exact TV configuration in which it would be installed. How is this done exactly, further reading you could suggest. I've ordered the exact replacement and trust no mod to the configuration is required.

    I did unknowingly purchase from a vendor who has been found by others here to be less than honest but the link was provide this thread with no warning! and Since I was requesting a source I took this as a link to a good vendor, naturally. . I just hope I'm lucky. I used PayPal so I would have “some” leverage in the event I encounter any issues. Bummer!
    My response to member nomoresonys was not intended to suggest you (Lotas) posted the link but somehow, my response to nomoresonys was directed to you which was not my intention. Very sorry that reply was apparently sent to you as it was not my intention to do so since you did not post that single link to this vendor.

    Leave a comment:


  • jkb242
    replied
    Re: Un55h6350afxza

    Originally posted by lotas
    You can order a board with a smaller or larger diagonal size, let's say "50" and then change it to your panel in service mode, then look for the number BN41-02157B, the main thing is that the connector matches yours (LVDS), and that it matches your region.
    Great info thanks. I suppose the board number you recommended was one that is more universal for this series and will accept the appropriate programming or paring with the exact TV configuration in which it would be installed. How is this done exactly, further reading you could suggest. I've ordered the exact replacement and trust no mod to the configuration is required.

    I did unknowingly purchase from a vendor who has been found by others here to be less than honest but the link was provide this thread with no warning! and Since I was requesting a source I took this as a link to a good vendor, naturally. . I just hope I'm lucky. I used PayPal so I would have “some” leverage in the event I encounter any issues. Bummer!

    Leave a comment:


  • lotas
    replied
    Re: Un55h6350afxza

    Originally posted by jkb242
    I just saw the link you posted to my thread. I thought it was a recommendation as a source which I had requested, but then I read the reviews today after I ordered.

    WHY WOULD YOU POST A LINK TO A SOURCE TO ANOTHER MEMBER LOOKING FOR A SOURCE WITHOUT STATING A WARNING DONT GO THERE?

    If you did this intentionally I'm shocked that a member here would do this to another unsuspecting member.
    I don't know anything about this site, I typed in the search and went to this site, so that you can see which numbers you need to pay attention to, and not order from this site.

    Leave a comment:


  • jkb242
    replied
    Re: Un55h6350afxza

    I just saw the link you posted to my thread. I thought it was a recommendation as a source which I had requested, but then I read the reviews today after I ordered.

    WHY WOULD YOU POST A LINK TO A SOURCE TO ANOTHER MEMBER LOOKING FOR A SOURCE WITHOUT STATING A WARNING DONT GO THERE?

    If you did this intentionally I'm shocked that a member here would do this to another unsuspecting member.

    Leave a comment:


  • lotas
    replied
    Re: Un55h6350afxza

    You can order a board with a smaller or larger diagonal size, let's say "50" and then change it to your panel in service mode, then look for the number BN41-02157B, the main thing is that the connector matches yours (LVDS), and that it matches your region.
    Attached Files

    Leave a comment:


  • jkb242
    replied
    Re: Un55h6350afxza

    Originally posted by lotas
    I did not mean to order from this site, I showed what part numbers should be for finding and ordering a motherboard.
    I was seeking assistance for a source as well since I haven't found any listed on Shop Jimmy or other providers I have used before. I just want to be sure that a replacement board would not require programming as I am unable to do this. Please advise. Thanks

    Leave a comment:


  • jkb242
    replied
    Re: Un55h6350afxza

    Originally posted by lotas
    You don't have to look for the motherboard if there is a programmer, then you need to read the data (dumps) from 25Q40 and 24C512, and if the software fails in them, then you can restore it.
    Are you saying this could be a programming issue that would not be addressed by a replacement board? If so I need to know ASAP as I do not have a programmer or reader. Do any of the replacement boards require programming?

    Thanks again!

    Leave a comment:


  • jkb242
    replied
    Re: Un55h6350afxza

    Originally posted by lotas
    Your number must be BN94-07845B, BN97-08043A
    https://www.tvpartstoday.com/BN94-07...n94-07845b.htm
    Thanks indeed for the assistance. The board model number on the sticker shows the exact board for this set to be BN-07259E which was in stock at the supplier recommended. I appreciate being told about this source as I was unaware of them. I ordered the exact board and agree that the sys board would seem to be the culprit given no other more classical failures. Much thanks will provide feedback when board is replaced.

    Thanks again for the assistance!

    Leave a comment:


  • lotas
    replied
    Re: Un55h6350afxza

    You don’t have to look for the motherboard if there is a programmer, then you need to read the data (dumps) from 25Q40 and 24C512, and if the software fails in them, then you can restore it.

    Leave a comment:


  • nomoresonys
    replied
    Re: Un55h6350afxza

    I'll take your word for it, I did not research it.

    Leave a comment:


  • lotas
    replied
    Re: Un55h6350afxza

    It does not matter.

    Leave a comment:


  • nomoresonys
    replied
    Re: Un55h6350afxza

    That board is for ver. UH02, his ver. is UH01, part number is different.

    Leave a comment:


  • lotas
    replied
    Re: Un55h6350afxza

    I did not mean to order from this site, I showed what part numbers should be for finding and ordering a motherboard.

    Leave a comment:


  • nomoresonys
    replied
    Re: Un55h6350afxza

    https://www.badcaps.net/forum/showth...t=tvpartstoday

    Leave a comment:


  • lotas
    replied
    Re: Un55h6350afxza

    Your number must be BN94-07845B, BN97-08043A
    https://www.tvpartstoday.com/BN94-07...n94-07845b.htm
    Last edited by lotas; 04-30-2023, 12:26 PM.

    Leave a comment:


  • jkb242
    replied
    Re: Un55h6350afxza

    Sorry I omitted the picture I referenced….
    Attached Files

    Leave a comment:


  • jkb242
    replied
    Re: Un55h6350afxza

    Originally posted by nomoresonys
    I think the problem is the mainboard isn't sending backlight on signal, which was my first thought. Sometimes a simple little test might lead down a different path, it's troubleshooting, assumption is not always good.
    I agree entirely in creating certain tests to further define the actual issue. One thing I also noticed after reconnecting the T-Con and with everything back to normal is that when pushing the set power on button, the standby LED blinks 5 times then extinguishes and does not repeat this cycle until the set is unplugged allowed to sit, then the same action could be duplicated. Not sure this offers any real insight. I would asked if there is anyway to apply a constant DC voltage to the BL PWM pin that would mimic the pulse “on duration” equal to approximate mid backlight drive just to get the backlights on. Purely a troubleshooting measure. What's your thoughts regarding this and an idea of the DC bias to use.

    Please see the attached picture of the system board noting the numerous board ID numbers. The one listed on the white label and the other one sulked screened on the board circled in red. I've searched EBay for the number on the label but replacement boards that are returned as being available do not match that of the board label of my set. Shop Jimmy has nothing available and appears to now sell everything on E Bay. This board is only 9 years old and well within what is traditionally available from Shop Jimmy I believe. Any sources you could recommend?

    Thanks!

    Leave a comment:

Related Topics

Collapse

  • m1ch43lzm
    HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
    by m1ch43lzm
    Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
    Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
    05-12-2025, 08:37 PM
  • Tynan Dill
    Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
    by Tynan Dill
    I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

    Upon bringing it home and plugging it up, it showed a standby light.

    I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

    The screen seems to blackout and stay black, but with a flashlight I can see the display.

    With my Playstation 4 connected via HDMI, and running a game I can hear sound.

    Assuming...
    11-22-2024, 01:46 PM
  • Hakuu
    LG OLED77G1PUA - No Video / Audio after a TCON Board change and Software Update
    by Hakuu
    Hi There,

    This TV was auto switching off after few seconds with some vertical lines on the screen, so got a new TCON board and replaced it.

    After replacing the TCON board it was working fine and i set it up with everything, used for few hours, then had the bright idea to update the software on it. During the update process, TV switched off and now no audio or video. No relay switch sound.

    More Details

    TV Model - LG OLED77G1PUA

    Got the same exact TCON board from TVPartsToday and replaced it. But didnt transfer the EPPROM data (didnt...
    07-12-2023, 02:37 PM
  • jb_Bak
    Sony xbr-65x900c main board issues?
    by jb_Bak
    Hey guys great forum glad to have found it. I bought a Sony XBR 65X900C cheaply because it didn't work. No signs of life at all not even a light/led. All I hear is a brief high voltage sound when I throw the power to it.

    Didn't see any obvious signs of damage so right away started checking voltages. This is what I see:
    Power Board Connector that goes to Main board
    CN6401
    Pin 01 NC
    Pin 02 NC
    Pin 03 "BL_ON": 0V
    Pin 04 "N/C"
    Pin 05 "STBY 3.3V": 3.5V
    Pin 06 "GND": N/C
    Pin 07 "AC_OFF"...
    09-27-2021, 04:52 PM
  • canadaboy25
    Panasonic TC-P54VT25 No image. A or D board?
    by canadaboy25
    I have a Panasonic TC-P54VT25 that will power on and prime the display but there is no image at all.

    The panel is primed as there is a slight glow from the entire panel. This means the problem should be logic related. The service manual also confirms this and recommends replacing the A or the D board.

    I have tried to get the TV to display the test sequence but I have been unable to and I don't even know if this TV has a test sequence or not. I tried following tom66's instructions in post #3 on this thread https://www.badcaps.net/forum/showthread.php?t=26790. There was...
    01-17-2021, 01:06 AM
  • Loading...
  • No more items.
Working...