SIThy Static Induction Thyristor ?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • massive
    New Member
    • Oct 2015
    • 3
    • new zealand

    #1

    SIThy Static Induction Thyristor ?

    Anyone know how to substitute could be made for a SIThy ? made by NGK

    http://www.doc88.com/p-194579522720.html


    by the looks of it , the main current is switched by mosfet , the Flyback transformer polarity flips , the diode becomes fwd bias and the SIThy gate gets its trigger to open . the SIThy is normally ON


    from the article:
    "the interesting point of this circuit is that with out any separate gate control circuit , the SIThy is turned off by forcing the device current to flow through its gate ,resulting in fast extraction of the carriers and the current cut off. Therefore , although the circuit control is carried out by using the FET , it is the SIThy that holds the induced voltage by L and plays the role of an opening switch."


    ...theres also a SIT = static Induction transistor , which I guess by the name is specific to Inductive Energy Storage
    Last edited by massive; 10-21-2015, 02:25 AM.

Related Topics

Collapse

  • Astonished
    Fixing the Charge Circuit of the Batteries of the DC Motor
    by Astonished
    Hi friends of electronics

    What you see in the video and pictures attached is the circuit for charging the batteries of a DC motor.

    The problem is that this circuit cannot charge the batteries (3 1800mAH NiMH batteries) any more. When the circuit was OK, its green LEDs lit up one at a time to show that the batteries have charged more. But now that the circuit is flawed, LEDs light up as you see in the video and at the same time successive beeps are heard.

    Please help me fix this circuit.

    (the datasheet of the IC: https://pdf.datasheet.live/28...
    01-28-2025, 06:24 AM
  • rddube
    Lenovo L490 Ram voltage circuit malfunction
    by rddube
    Hello friends,

    Looking for some guidance here. The RAM voltage circuit on this motherboard keeps burning out PU301 which is a RT8231AGQW. Copy of the board with the burnt chip attached with some voltage measurements and copy of the schematics also included.

    I think I've checked almost every component in the circuit, but when I change the RT8231, the laptop starts I have 1.2V on the inductor for about 10 seconds and then the RT8231 goes south and no more voltage on the inductor. All other voltages on the laptop are good, this is the only one conking out for a reason I...
    07-15-2025, 04:41 PM
  • Crystaleyes
    Omega MML200 Coutant Lambda PSU repair
    by Crystaleyes
    Hi all.

    Recently I picked up a vintage HP 37717B communications analyzer which uses one of these MML200 Coutant power supplies. Needless to say the PSU is not working, and surprisingly there is apparently nothing available on the web regarding repairing one of these. No stories, no schematics, zilch!
    There are however many companies offering repair 'services', however I don't have the luxury of sending it off, so am intending to do the repair myself.

    I admit right now that I am no expert on smps repair, although I do have a grasp on the principle of the general...
    05-29-2024, 08:23 PM
  • Tarot Superstars
    Short Circuit tester
    by Tarot Superstars
    Hello.
    I have seen a short circuit tester made with 3 * 9V batteries, a voltage limiter component and a resistor connected to the probes of a multimeter.
    The theory is that the meter becomes sensitive enough to read very low resistances and the lowest resistance to ground on a circuit is likely to be a short circuit in that area.

    Link
    The Amazing $1 Short Finder Upgraded! Convert ... - YouTube
    https://www.youtube.com/watch?v=0eixDdCpiO4

    My multimeter isn't normally sensitive to very small resistance, but when I put a 1 mega ohm resistor...
    09-25-2023, 09:11 AM
  • Lvsitano
    Asus X532FL 3.2V at source and gate
    by Lvsitano
    I am having some trouble with troubleshooting a Asus X532FL rev 2.0 motherboard, which does not power on. So at the first MOSFET, I am getting 19V at the drain, and then 3.2V on both gate and source (compared with ground). Of course, the 2nd MOSFET's source will have 3.2v at source.

    First MOSFET is a QM3056M6 and 2nd MOSFET is a QM0930M3

    I already checked first MOSFET and source and gate are not shorted (drain with source not shorted either). Also I have 1.7V at the LDO rail (measured at the keyboard connector, as the power button is on the keyboard).

    First...
    06-26-2024, 02:13 PM
  • Loading...
  • No more items.
Working...