CTE Battery Charger

Collapse
X
 
  • Time
  • Show
Clear All
new posts

Related Topics

Collapse

  • Document Archive
    ISL88739AHRZ ISL88739 Laptop Battery Charger Datasheet
    by Document Archive
    The ISL88739 & ISL88739AHRZ are a highly versatile combo battery charger
    configurable for operating as either a Hybrid Power Boost (HPB)
    charger or a Narrow VDC (NVDC) charger, supporting 2-, 3-, or
    4-cell batteries. Both configurations allow the battery to work with
    the adapter together to supply the system load when it exceeds
    the adapter capability, referred to as system Turbo mode. HPB
    charger configuration reverse-boosts battery energy to the system
    bus to help the adapter provide the system power in Turbo mode.
    NVDC charger configuration...
    11-05-2024, 03:28 PM
  • Document Archive
    ISL6257HRZ ISL6257HRZ-T Laptop Battery Charger Datasheet
    by Document Archive
    ISL6257HRZ ISL6257HRZ-T Laptop Battery Charger Datasheet

    Highly Integrated Narrow VDC Battery Charger for Notebook Computers

    The ISL6257HRZ ISL6257HRZ-T is a highly integrated battery charger controller
    for Li-Ion/Li-Ion polymer batteries. ISL6257 is designed for
    Narrow VDC applications where the system power source is
    either the battery pack or the regulated output of the charger.
    This makes the max voltage to the system equal to the max
    battery voltage instead of the max adapter voltage. Operating
    at lower system voltage can improve...
    11-05-2024, 04:43 PM
  • flat-earther
    how to prevent a connected charger from draining battery when not charging?
    by flat-earther
    I have an RC radio handset(Taranis QX7) which doesn't have internal battery charger which means I had to remove the battery every time I needed to charge it.
    So to improve it, I added a 15W USB-C charger board(link) inside and soldered it to the same connector on the PCB where the battery plugs into, great, now I can simply charge it with a USB-C cable.

    but the problem I found is that after the radio sat for two weeks without being used the 2S 18650 battery that I'm using was at 4.2V!
    So the battery is backfeeding the charger and being drained.

    How can I prevent...
    08-07-2025, 01:04 PM
  • sam_sam_sam
    Bauer tool battery pack charging with a HERCULES charger modification
    by sam_sam_sam
    The Bauer power tool battery charger just has to many issues with the charger over heating because I several HERCULES Hercules battery chargers that are 3 amp charge and because they have gone on quite a few times over the years before they came out with the fan cooling battery charger I going to modify one so I can charge Bauer battery packs faster than the crape battery charger that they have

    Here is how this modification is going to be done I taking a 1.5 amp hour battery enclosure and gutting it removing the battery cells and replacing some Ryobi 1.5 amp hour battery pack that...
    05-06-2023, 12:17 PM
  • sam_sam_sam
    Milwaukee M18 HD12.0 (12 amp hour battery pack) unbalanced failure charger refusing
    by sam_sam_sam
    I have two Milwaukee 12 amp hours battery packs that have an issue with battery cells very unbalanced these are probably over 4 years old and been heavily used in the past but now get occasionally used heavily and when I went to use the grinder tool the battery lost battery battery power very quickly so I decided to open it up and found some battery cells voltage from 3.6 to 4.1 no wonder the battery charger was not fully charging them 3 out of 4 LEDs were on meaning that it was only 75% charged

    So I have put them on the battery testing machine to drain each battery cell down to...
    09-04-2022, 04:45 PM
  • Loading...
  • No more items.
Working...