Resistor Identification

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Mufasa
    Member
    • Nov 2022
    • 26
    • usa
    #1

    Resistor Identification

    Hello everyone,
    I need to replace a resistor but I'm having a bit of trouble deciphering the colors - a little color blind.
    Looking for the value of R91.

    Can anyone help.

    Thanks in advance.
    Attached Files
    Tags: None
    • lotas
      Badcaps Legend
      • Jan 2016
      • 4459
      • Russia
      #2
      1kOm 5%

        Comment

        • Mufasa
          Member
          • Nov 2022
          • 26
          • usa
          #3
          Thank you!

            Comment

            Previous template Next

            Related Topics

            Collapse
            • jinu_j
              Dell 2209WA - power supply - Fusible Resistor replacement
              by jinu_j
              Hi

              I am trying to repair an ancient Dell 2209WA Monitor which suddenly shut off with a pop sound. On investigation found that one of the fusible resistors had blown. Further investigation identified multiple components as faulty because of which the fusible resistor blew. Please refer the attached circuit diagram showing the components that were found to be damaged.

              1. FR950 - blown fusible resistor - 0.2 Ohm 1W
              2. Q950 - shorted Q950 MOSFET - 650V 10A N Channel Mosfet
              3. R835 - Blown Resistor - 20KOhm SMD resistor
              4. D930 - Shorted Schottkey Diode...
              05-03-2025, 10:51 PM
            • GottaBeGrim
              PNY RTX 3060 12GB single fan resistor identification
              by GottaBeGrim
              hello, i have the gpu in the title and a resistor fell off that i need help finding the resistance of. does anyone have the schematic or the resistance value? see images below for the one missing....
              2 Photos
              01-02-2025, 08:11 PM
            • mikey5791
              Need help to replace burned resistor in 350w atx psu
              by mikey5791
              Hi to all forum members,

              Got this faulty 350 watt atx psu dirt cheap from a local online seller as i am keen to use it as a learning tool to repair faulty power supply.
              The faulty part is quite obvious from the burn area near the 16pin KA7500 BD pwm. The fuse is still intact with good continuity.

              Upon power on ac, there is 5vdc standby power on cathode of diode D14 and about 10vdc on cathode of diode D13.(This should be the aux power to generate the 12v and 5v rail.)
              Initially i replace the two burned resistors near my marked red arrow to 200 ohm resistor...
              12-26-2024, 04:55 AM
            • MidnightRoller
              Can a resistor lose resistance after hot air?
              by MidnightRoller
              I am curious if a 0402 resistor could go from 43 ohm to 0. In electronics class and my experience a resistor can degrade and gain resistance all the way up to not being able to conduct at all. I have never heard of a resistor decreasing in resistance and becoming 0 ohm or a dead short… that's not the direction they fail… or so I thought.

              I was attempting to remove a wson8 chip on an iMac motherboard and it required a lot of heat, on one side of the chip were 3 0402 resistors that were very close. I popped the chip out unintentionally out of the tweezers and sent those resistors...
              02-02-2022, 11:46 PM
            • redbaron1007
              Klein MM400 resistor identification
              by redbaron1007
              I managed to blow the fuses in my Klein MM400 multimeter and when I replaced them I was still getting a cal and error0 message. I started looking around the board and found one resistor that was testing OL and has a visible burn mark on the top of it so I can't tell what the value is anymore. Its marked as R19 on the board and I included a picture below of what it looks like.

              ​

              Does anyone know from working on these what the value is or have this exact meter they could open up and check the value? It's not my only meter, but it is my first real non harbor freight meter...
              07-24-2024, 03:53 PM
            • Loading...
            • No more items.
            Working...