please clear me this bios efi macbook macbook pro 13 inch a1278 820-2879
-
Hey! This is a A1278 macbook 2011.
Problem: Not turning on / No green light
Im using by3200s charger.
Voltajes:
PPBUS_G3H = 12.26v
SMC_RESET_L = 3.3v
PP3V42_G3H = 3.42v
U7000 =
Pin 1 CHGR_AGATE = 0v
Pin 2 CHRG_DCIN = 19v
Pin 3 CHRG_ACIN = 4.6v
Pin 10 SMBUS_SMC_BSA_SDA = 3.3V
Pin 11 SMBUS_SMC_BSA_SCL = 3.3V
Pin 12 PP3V42_G3H = 3.42v
Pin 13 CHRG_RST_L = 3.3V
Pin 14 SMC_BC_ACOK = 0.8V
Pin 19 PP5V1_CHRG_VDD = 5.05V
Pin 20 PP5V1_CHRG_VDDP = 5.03V... -
Hello, I am looking for any and all files related to the mainboard for 820-2565-A (13" Macbook Pro A1278 mid 2012) schematics/board view.
I looked through forum search results and google and was unable to find a board view file, I found a pdf of all the schematics but I don't know where the parts physically are on the board as this is my first macbook board level repair attempt.
The macbook charger has a green light, the battery has been replaced and OS reports Normal status but Not charging. After cleaning a corroded capacitor it crumbled off the board. There... -
Subject: Help Needed: MacBook A1278 (3115) No PPBUS_G3H Issue
Hello everyone,
I'm working on a MacBook A1278 with the 3115 logic board and facing an issue with no PPBUS_G3H voltage. Here's what I've checked so far:- U7000 Measurements:
- Pin 3 has 0V, even though R7012 shows 16.5V from PPDCIN_S5_CHGR.
- Resistors:
- I measured R7010 and R7011 with one leg disconnected, and both tested OK.
Based on these findings, I believe U7000 needs to be replaced. However, I have a related question:- If I also decide to replace the SMC, do I need to order it pre-programmed,
- U7000 Measurements:
-
Hi,
I have a MacBook Pro 13 inch A2238 M2 and it was stuck 5V with 0 amps. I measured some important lines and I found a short on PP3V8_AON_MPMU_ISNS_VIN, I tried injecting 1v and I saw heat coming from the mPMU so I removed the pmu thinking that was the problem. I don't know why I didn't check the other side of the border but there it was, a shorted cap. I replaced the cap and the short was gone, so I reballed the PMU and put it on again but voltage was still stuck at 5V and the current was fluctuating between 0 and 0.45 amps. I checked under the thermal camera and I saw the mPM...04-02-2025, 05:02 PM -
Hi everyone!
I have a 2018 MacBook Pro (with Sequoia OS) that I've been using for years with no problem. I recently received an M2 MacBook Pro so I'm mostly using it and not the 2018 one, but since a friend of mine needs a computer, I thought I could restore my 2018 and give it brand-new-like to my friend.
I tried using the built-in tool to restore the MacBook (Settings > General > Transfer or restore > Delete) but it got stuck when trying to remove the Find Device configuration (it asked me for the password for my old Apple ID -now I use the same account but...06-27-2025, 08:54 AM
Comment