how to program mec 1416 -nu
EDI54 la-g712p rev 1.0
EDI54 la-g712p rev 1.0
-
-
I'm sorry to correct you, but that's not the truth. I just replaced this SIO and without programming this laptop wont start.
The laptop I'm repairing now is DELL P75F (Dell G3 15 3579) Service Tag G3GKKP2 (MFG Year 2018)
White silk motherboard markings are
Vendor tmt YAML 1
E114139
94V-0
CAL53 LA-F611P REV':1.0)A00
The chip is MICROCHIP MEC1416-NU (D1810-A2Q2F3 810CA3A) 32 pins per side X 4 sides - for a total of 128 pins
Go to this link and search the site for the chip number and you ll see bud.
https://www.badcaps.net/forum/troubl...e3#post3597660
I am gonna have to buy a SVOD SIO programmer to program this chip to finish this repair.
If anyone have the program for me to write, please upload.
Love you all,
Love this website.Comment
-
ene kb9012 programmable
ene kb9016 programmable
ene kb9018 programmable
ene kb9022 programmable
ene kb9028qc programmable
ene kb9010 programmable
ene kb3930qf/b1 programmable
ite it8585e programmable
ite it8586e programmable
ite it8985e programmable
ite it8587e programmable
ite it8522 programmable
ite it8987e programmable
ite it8589 programmable
ite it8522 programmable
ite IT8380E programmable 192kb
ite IT8380VG programmable 192kb
ite IT8995E-128 programmable
ite it8886H... -
Hi electronic folks
Does anybody know if this controller is programmable or not ?
I have replaced this controller on a MSI MAG B560 TOMAHAWK board, as it had a short on VCCS pin (pin 41). I have ordered a few new on Aliexpress, they seem to be original, however they do not start to work. When I move same chip from a second working board to the one I have replaced the RAA229001, the VRM starts normally to work. It seems that the chip is OK, as it generates on the VCCS pin nearly same voltage as a chip on a second working board i have (VCCS probably it's some internal reference... -
Model number VPT24-16Z.
https://leviton.com/products/vpt24-16z
I have 3 of these in my home for over 10 years now and Im planning on replacing them as I lean towards a Philips Hue home setup.
They are great units but they lost the ability to keep/store the time and settings after power outages and brown outs.
I knew it was a battery in there somewhere but never got around to looking into it.
Well an opportunity came for me to remove this from its home in my wall so I disassembled it to see what was going on.
I found a 3.6V LIR1632 battery spot... -
Hi all
The culprit ELEWAY BF24-1A-H-S 24VDC relay.
Item a programmable outlet Brennenstuhl dt v2. It just won't turn on and off when it should. The reset works fine but I do not hear the relay clicking on/off. I have two of these outlets, one works fine the other one not even close. I think it is the relay but I cannot find it to buy. Also I cannot find a similar one. I cannot find a datasheet for this relay. So I am stuck. Any help, any ideas will be greatly appreciated. -
please help i need a schematic or board view for Dell Inspiron 3580 EDI54 LA-G712P rev 1.0(a00)..
issue is it powers on with no display.. when powered on holding "D" it runs the display TEST showing all the colors. i have flashed it with Clean ME files, all same results =No display.
on the PSU it powers up then 0.10mA .....> 0.30mA ....> 0.60mA then caps lock goes off and laptop goes to 0.35mA no fan nothing.. but CPU gets warm.
please help...
Comment