A1534 820-00244-a

neo1967

New Member

Join Date: Jan 2020

Posts: 2

Country: cyprus
#1

A1534 820-00244-a

01-04-2020, 02:36 AM

hi
am new here and i have a question,if you can help,
i was loading Catalina on A1534 and at the end of installation i end up with a logo and bar going to the end,then again and again the same think.
so i had the idea to lift the board from the battery to stop this boot loop,now i have a board that does not start.
do you know what can cost this problem?
thank you in advance.
Tags: None

Previous template Next

Fit 820-00244-А board in Apple Macbook A1534 2017 820-00687-А

by stefanbs

The laptop is Apple Macbook A1534 2017 with board 820-00687-А. The USB-C tester shows no voltage, there is 820-00244-А board available. I looked at both schematics, all connector signals seem to be the same. Did someone try to fit 820-00244-А board in A1534 2017?
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
05-11-2025, 01:08 AM
Macbook A1534 820-00244 - 5V 0,2A

by obelix24

Hi All,

i got one Macbook a1534 boardnumber 820-00244 that is taking only 5V 0,2A

I've tried to replace 3x CD3215B01 chip but it's still behaving same ....

On the board there was blown L4804 so i've replaced it.
when power is connected 5V 0,2A
PPBUS_G3H - 0V
PP20V_USBC_XA_VBUS_F - 5V

I've tried to remove F7040 as mentioned here
https://www.badcaps.net/forum/troubl...1534-820-00244

but there is...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
04-29-2024, 07:48 AM
Reebok one GT40s treadmill lift motor runs at switch on

by G0RIT

Good evening I am working on a Reebok oneGT40s treadmill. It had a flashing display which the replacement of D3 rectified. However the lift motor now runs when the mains is turned on and does not stop. If I then select start so the tread motor runs and disconnect the up lead to the lift motor it stops. If I then reconnect the lead the lift motor works as it should with the controls. It will continue to work correctly until the mains is turned off and on again, or the safety device is removed and replaced. It then runs again and only by disconnecting and reconnecting the up lead will it operate...
- Channel: Troubleshooting Power Supplies and Power Supply Design
06-23-2022, 05:57 PM
a1534 ssd not detecte

by Arshad alam4659

i havw a a1534 820-00244 in this board ssd not detected i open the laptop u8600 cover is burn mark i have a same board Can I replace this IC with another same board
what is this ic
- Channel: Laptop, Tablet, & Notebook Specifications
01-02-2025, 09:13 AM
MacBook Pro 16” 2019 Boots installs os Catalina but won’t install Ventura or lower.

by Stephen

So got an issue, did a DFU recovery for a 16” we have.
It will install Catalina from internet recovery perfectly fine.

Tried upgrading to Ventura, no bueno, so created bootable installer of Ventura. Nothing it just gets hung up at the half way point for over 24 hours.

No water damage on board. Board is clean. Any idea why this is?

All ports works

Did a DFU RECOVERY AND RESTORE, twice with success and successfully reinstalled Catalina. But it seems it won't install anything higher. Any suggestions would be great.
...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
05-19-2023, 10:53 AM
Loading...
No more items.

A1534 820-00244-a

A1534 820-00244-a

Related Topics