Panasonic CF-C1 no 5V on usb ports

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Fabbrone
    Senior Member
    • Jun 2015
    • 158
    • italy
    #1

    Panasonic CF-C1 no 5V on usb ports

    Good morning, this laptop has USB ports that does not have the 5V

    do you have any idea if recoverable or is the chipset

    TOUGHBOOK cf-c1 i5 mainboard DFUP 1999zc

    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • DynaxSC
      GIGABYTE X299 AORUS ULTRA GAMING - SATA PORTS 4-7 NOT WORKING ???
      by DynaxSC
      Hi,

      I have the above mentioned bord after repair, which was related to a lot of missing smd devices on the back of the board.
      There were almost 20 devices missing, caps, resistors and some diodes/mosfets.
      The board is generally working now, all PCIe ports are working, Windows installs normally.

      However I have a problem with SATA ports 4-7 (the board has 8 SATA ports) - disks are not beeing recognized by the BIOS neither by Windows (which is usually normal in case BIOS does not recognize them).
      The SATA 4-7 driver network is quite simple chipset<->buffers/drivers<->SATA...
      03-10-2025, 12:27 PM
    • aa10aa10
      Panasonic Toughbook CF-33 mk1 BIOS repair
      by aa10aa10
      Good day,

      I have tried to remove BIOS supervisor password from Panasonic Toughbook CF-33 mk1. Model number CF-33AENABTG, unfortunately I don't have any other info.

      I read the BIOS using afuwin, edited it and tried to flash new edited BIOS using afuwin. Unsuccessfully. Afuwin showed "Error: Problem erasing flash." starting with 0x00040000 and stoped. Then I tried many other options to flash BIOS from Windows without any luck. Finally i rebooted the device - and no post. Afterwards I have read the corrupted bios chip (MX25L12873F) using EZP2010 programmer....
      01-21-2025, 06:13 AM
    • eukal
      Panasonic toughbook cf-h2 Mk1 no power, 3.3v-5v present but no 3v on bios chip
      by eukal
      Hello, i have a Panasonic Toughbook Cf-H2 Mk1 that won't power on. The battery charge without problem but no response from the laptop when i press the power button.
      I have disassemble and unpluged the cmos battery, same no power on on battery with and whitout the adapter, and only adapter
      I have check the voltage i have the main power rail ( +-16v normal for toughbook it's not 19v). I have on the coil after power management chip 3.3v and 5v.
      I have check the 3.3v on the power button ribbon cable attach to the motherboard and the voltage go to 0v when i press the button. So...
      07-01-2023, 01:00 PM
    • Nedim Merdan
      Panasonic toughbook CF-D1DW200FZ motherboard DL3UP1969CAA schematic
      by Nedim Merdan
      Does anyone have the schematic for toughbook cf-d1 mk1 motherboard model is DL3UP1969CAA thanks in advance
      12-07-2024, 02:22 PM
    • David Smedley
      Panasonic FZ-55 Toughbook main board schematic request
      by David Smedley
      I've been working on this awful project with a Panasonic FZ-55, basically I'm trying to intercept the eDP signal from the main board, and replace it with my own eDP signal connected from an lcd driver. The problem is, for some reason the 30 pin ribbon pinout is really unusual and not playing nice with my LCD controller. Long story short, I managed to fuck up my board and pull off some pads on the eDP out port, I'm hoping to find either another eDP out source somewhere else on the laptop, or figure out this goddamn pin layout so I can just replace the whole native display complex with my controller...
      09-04-2024, 02:57 PM
    • Loading...
    • No more items.
    Working...