K56cm fan always on and maximum speed after reprogramming

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • jasko_jacker
    Badcaps Legend
    • Oct 2014
    • 1137
    • italy

    #21
    Re: K56cm fan always on and maximum speed after reprogramming

    35° with fan at maximum speed but if you stop the fan for a moment and it reach ,for example, 90° C instantly , probably there is an issue with gpu.
    You can try another method, install msi afterburned and change the freq of the videocard at his minimum; in this case the temp must go down but not with a fault.

    Comment

    • Djosla
      Badcaps Veteran
      • Dec 2012
      • 246
      • Montenegro

      #22
      Re: K56cm fan always on and maximum speed after reprogramming

      those dumps and me region is ok...culprit is somewhere else...might be something with sio...

      Comment

      • ala_borbe
        aka Donald
        • Apr 2011
        • 1625
        • Malta

        #23
        Re: K56cm fan always on and maximum speed after reprogramming

        @Djosla

        my clean me dumps are not working... how did you do yours with fitc or hex editor?
        Im Back... sort of...

        Comment

        • Djosla
          Badcaps Veteran
          • Dec 2012
          • 246
          • Montenegro

          #24
          Re: K56cm fan always on and maximum speed after reprogramming

          you have pm...

          Comment

          • magnetepazzo
            Senior Member
            • Feb 2017
            • 85
            • italy

            #25
            Re: K56cm fan always on and maximum speed after reprogramming

            Hi friends thanks to all for help, and to end I have put a resistor to power of fan and have reduced the noise . Any dump I have tried haven't resolve the problem. Thank to all.

            Comment

            Related Topics

            Collapse

            • Babbar
              1980s Holz Her 2420 belt sander - Only works when speed control at maximum
              by Babbar
              My fathers belt sander from the 80s which i very much would like to continue using has an issue with the speed control. The machine works fine on maximum speed but will not turn or give any sign of life when on any other setting. The speed control is a dial going from 1-6 although implemented as a potentiometer without distinct steps. I took the machine apart and measured each component individually, all components and measurements have been captioned in the attached pictures. The Triac did not get identified correctly using my cheapo component tester, i don't know if this is user error, if the...
              11-13-2024, 01:54 AM
            • japlytic
              Maximum speed should be marked on network ports
              by japlytic
              I noted that a number of consumer entertainment devices have the maximum speed marked on the wired network port and considering that there are broadband plans faster than 100 Mbit, the wired network port can be a bottleneck since some routers do not have Gigabit (only 100 Mbit) support for the WAN port let alone the wired network ports.

              One other thing: Certain low cost network cables only have two pairs which limits speed to 100 Mbit.​
              12-19-2024, 05:04 PM
            • tofik
              MOSFET equivalent K8A60DA
              by tofik
              Hello guys,

              I have a shorted MOSFET K8A60DA with the following characteristics:
              Type Designator: TK8A60DA
              Marking Code: K8A60DA
              Type of Transistor: MOSFET
              Type of Control Channel: N -Channel
              Maximum Power Dissipation (Pd): 45 W
              Maximum Drain-Source Voltage |Vds|: 600 V
              Maximum Gate-Source Voltage |Vgs|: 30 V
              Maximum Gate-Threshold Voltage |Vgs(th)|: 4 V
              Maximum Drain Current |Id|: 7.5 A
              Maximum Junction Temperature (Tj): 150 °C
              Total Gate Charge (Qg): 20 nC
              Rise Time (tr): 25 nS
              Drain-Source
              ...
              07-19-2023, 05:18 AM
            • Document Archive
              DELL Vostro 3580 Notebook 3000 Specification for Upgrade or Repair
              by Document Archive
              This specification for the DELL Vostro 3580 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the 3580 boardview and 3580 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download for DELL Vostro 3580 Notebook...
              09-06-2024, 09:17 AM
            • Document Archive
              DELL Vostro 3581 Notebook 3000 Specification for Upgrade or Repair
              by Document Archive
              This specification for the DELL Vostro 3581 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the 3581 boardview and 3581 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download for DELL Vostro 3581 Notebook...
              09-06-2024, 09:17 AM
            • Loading...
            • No more items.
            Working...