Help identifying chip ProBook 650 G5

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Kwisatz Haderach
    Member
    • Aug 2015
    • 15
    • Spain
    #1

    Help identifying chip ProBook 650 G5

    Can someone help me identify this chip?
    U3003 board 6050A3028501 - MB - A01 (scheme not available) ProBook 650 G5
    Marking code j7 0b0?
    Package DFN6 1x1.5mm
    Pin 2 : GND
    Pin 5: 3,3V
    Near LVDS conector.

    Thanks in advance.

    ​
    Attached Files
    Tags: None
    • mon2
      Badcaps Legend
      • Dec 2019
      • 14351
      • Canada
      #2
      Could be this one (used on similar boards from HP):

      Click image for larger version Name: mystery_part2.png Views: 127 Size: 122.2 KB ID: 3312409



      Part # 74LVC1G3157FZ4 (can be replaced with NXP = Nexperia 74LVC1G3157GM

      74LVC1G3157 (diodes.com)​


      Click image for larger version Name: mystery_part1.png Views: 134 Size: 96.1 KB ID: 3312408

        Comment

        • Kwisatz Haderach
          Member
          • Aug 2015
          • 15
          • Spain
          #3
          Thanks for the information🙏
          It's an analog switch! 🤦‍♂️
          My board has the missing component and there is no image on the panel
          I'm going to try short 1->4 or 3->4
          At the moment I have not found any donor board in my scrapyard​

            Comment

            • Kwisatz Haderach
              Member
              • Aug 2015
              • 15
              • Spain
              #4
              Finally I connected pin 1 to 4 and the laptop is working. Thank you very much mon2

                Comment

                • mon2
                  Badcaps Legend
                  • Dec 2019
                  • 14351
                  • Canada
                  #5
                  Awesome A bit of good news to start the day here.

                    Comment

                    Previous template Next

                    Related Topics

                    Collapse
                    • acedogblast
                      Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
                      by acedogblast
                      This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

                      There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
                      11-02-2024, 05:13 PM
                    • DynaxSC
                      ASRock B650M PRO RS - BIOS CHIP 25Q256JW BLOCKED BY STATUS REGISTERS
                      by DynaxSC
                      Hi

                      I have a very strange issue with the BIOS SPI chip of an ASRock B650M PRO RS motherboard.
                      The SPI chip is an Winbond 25Q256JWEQ model (1V8).
                      The motherbaord doas not POST - it lits only CPU and DRAM EZ Debug Leds, and stays that way forever.
                      The Flashback function of the motherbaord is also not working, despite all instructions followed correctly - I'm 100% sure of this.

                      I have then desoldered the chip, backupped the contents, and tried to earease the chip in order to program stock image, but the chip is locked by status registers SREG2 (TB) and SREG6...
                      08-04-2025, 12:20 PM
                    • Loki_Fido
                      Requesting help identifying chip in Macbook Pro A2485
                      by Loki_Fido
                      Hi ya folks,

                      I have this MacBook Pro A2485 (M1 Pro 2021) which came in for repair.

                      It had a shorted SSD power supply chip. Therefore it was stuck at 5V.
                      I replaced it and the SSD are fine. No more shorts.

                      But The mac still pulls 5V and 200mA. If i leave it alone for 5 mins, the mac manages to receive 20V and 40mA. Of course, which doesnt mean the mac starts after power meter reading 20V.

                      But while the mac is stuck at 5V, i checked the board with thermal and found this chip was trying to start. Chip picture is attached.
                      Chip marking...
                      08-07-2025, 10:17 PM
                    • SMDFlea
                      Common SPI bios chip programming Questions and Answers
                      by SMDFlea
                      Common SPI bios chip programming Questions and Answers
                      ----------------------------------------------------------

                      Q: I have a bios request,i can`t post my backup as i can`t read from the chip.

                      A: If you can`t read from it how do you expect to write to it ?.

                      Q: Why is my bios chip unreadable ?.

                      A: The programmer is faulty or has a worn or broken zif socket.

                      The USB cable is frayed,connector pins worn or some other physical damage.

                      Not enough amperage or voltage to power the programmer properly.

                      Bad...
                      09-02-2021, 04:40 PM
                    • trepachka
                      Help identifying this chip for Yoga 7 16IRL8
                      by trepachka
                      This chip is shorted thru. Based on what I see, it's either a 3.3V or 5V buck converter, just my guess. The markings on the chip state "S2=AB".

                      A photo of the chip is attached.

                      Thank you....
                      06-22-2025, 11:13 PM
                    • Loading...
                    • No more items.
                    Working...