Troubleshooting Uni-T EEPROM ErrE

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • stj
    Great Sage 齊天大聖
    • Dec 2009
    • 30951
    • Albion
    #21
    Re: Troubleshooting Uni-T EEPROM ErrE

    it's posted further up in post #5 ,
    but you need to calibrate afterwards because every meter is a little different.

      Comment

      Previous 1 2 template Next

      Related Topics

      Collapse
      • SidneyCanadas
        93C46 and 93C56 EEPROM
        by SidneyCanadas
        I tore apart my instrument cluster for my 2008 Toyota Corolla made in 2007 in Cambridge, Ontario, Canada and pcb location: IC6=EEPROM is a surface mounted device with part # of 93C46W7, some claim the EEPROM out of a Camry part # 93C56 will allow odometer to roll over 299 999 KM or miles. The data sheet for both is below:

        https://cdn.badcaps-static.com/pdfs/...c6e42b20d3.pdf 2

        Anyone know if the Camry one will work on my Corolla?. And which EEPROM reader/writers do you all recommend I purchase that will allow me to read the old values of the old...
        06-14-2023, 01:16 PM
      • bauto601
        KDM 480W PSU upgrade succes! (opinions?)
        by bauto601
        Back in 2020 i bought a (2nd hand) compact ATX psu to replace my current one. My PC case only fits very short ATX power supplies so i didn't really have the choice of buying a decent 80Plus unit. The current unit is a modded YoungYear unit that i made a thread about a while ago:
        A "nice" YoungYear unit? - Badcaps

        The "new" unit is a KDM-M6480 480W psu, the 480W number is a typical KDM bullshit claim of course, but the 24A rating on the 12V rail seemed reasonable and the "Active PFC" claim gave me a bit of hope that this was going to be decent-ish....
        12-26-2023, 03:05 PM
      • Habble7
        I need a BIOS dump for the Samsung S49CG934SU monitor
        by Habble7
        The Samsung S49CG934SU monitor does not power on - no LED indicator activity and no response to power button. However, when 21V power is connected, it immediately draws 0.8A of current with no display output. The motherboard processor gets warm, and there is continuous reading activity from the W25Q128BV BIOS chip.

        Suspected Cause:
        I suspect the BIOS may have been corrupted during a power interruption while updating the firmware. The official website provides firmware updates, but they can only be installed via USB flash drive.

        Troubleshooting Attempts:
        ...
        05-22-2025, 07:28 AM
      • blues_spirit
        practical courses for troubleshooting pc motherboards
        by blues_spirit
        Hello from France,
        mon2 kindly advised me to post a thread to ask the question(s) I'm concerned about. I'm new to the forum and I'm looking for practical courses for troubleshooting pc motherboards especially laptops in Europe, if possible in France. I have been a computer network system administrator and a corrector of administration modules for automated programs under Unix. But I really miss the practical "ops" side of troubleshooting. So I would like to start from the beginning: 1.8V, 3.3V, 5V and 19V tests for example, etc...
        Do you think this is feasible for me? I...
        12-18-2022, 12:56 PM
      • edgarmg15
        Damaged EEPROM on TV Vizio E320-A0
        by edgarmg15
        Hi everyone

        I´m trying to repair a TV Vizio E320-A0 that I found in the street

        The symptoms are it doesn't respond with remote or buttons, the LED indicator is always off and also there is no image on the TV.

        The power supply board works fine (I probed the terminals with my multimeter) but in the main board the EEPROM doesn't works correctly because the voltage on the pins doesn't match with the parameters of the datasheet.

        So, I´m going to replace the EEPROM with a new one, but the problem is that my programmer (CH341a)...
        11-19-2022, 03:46 PM
      • Loading...
      • No more items.
      Working...