Nintendo Wii power supply

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • Eaglecrest
    Senior Member
    • Jul 2018
    • 147
    • United States
    #21
    Re: Nintendo Wii power supply

    Sorry for the delay, but here are pictures from a US supply for Heihachi_73.

    I replaced the bulging smaller cap on left middle and the power supply works like a charm, can't same the same for the Wii.
    Attached Files
    Last edited by Eaglecrest; 01-12-2021, 08:00 PM.

      Comment

      • stj
        Great Sage 齊天大聖
        • Dec 2009
        • 30997
        • Albion
        #22
        Re: Nintendo Wii power supply

        that seriously does not look like i would expect from nintendo.
        although i never opened a wii psu, i am 99% sure that's a 3rd party replacement.

          Comment

          • Eaglecrest
            Senior Member
            • Jul 2018
            • 147
            • United States
            #23
            Re: Nintendo Wii power supply

            Might be, it was what came with the unit, but it is a hand me down. When i get a chance i will check the one that came with my original unit (new).

              Comment

              Previous 1 2 template Next

              Related Topics

              Collapse
              • sam_sam_sam
                Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
                by sam_sam_sam
                I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

                One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
                03-31-2024, 02:12 PM
              • sam_sam_sam
                Modification to a ZD-987 desoldering/soldering station using a external switching power supply
                by sam_sam_sam
                I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

                I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
                07-01-2024, 06:34 AM
              • JimBanville
                Definitive technology SC 2000 subwoofer amp's power supply clicking and popping
                by JimBanville
                The sub developed a constant popping every couple seconds from woofer and power LED flickering with nothing but wall AC connected. Connecting an audio cable didn't change anything. It doesn't play but a second or two of audio in between the pops.
                Opened it up and discovered the power supply is making a faint clicking or ticking sound.
                I measured the amp's output to the woofer and it pulses up to 50mv DC to be driver. The pulses coincide with the power supply ticking/clicking.
                I measured the power supply output going to the amp board and it too has this pulsing. Voltage cycles...
                09-13-2023, 07:21 AM
              • shovenose
                Christmas Light Power Supply Question
                by shovenose
                Hi all,
                I have a cheap rainbow christmas light set off Amazon which has this little power supply that has a button to change modes. I had a white set with the same power supply that I returned but I can't find any other rainbow themed ones that don't use this setup.

                Anyway, the problem is every time you unplug them and then plug them in it reverts back to "Combination" mode which cycles through all these annoying tacky effects instead of going back to what you had selected or at least defaulting to "Steady on" which is what I want. So I'm thinking I can just...
                1 Photo
                12-08-2023, 09:59 AM
              • Tynan Dill
                Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                by Tynan Dill
                I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                Upon bringing it home and plugging it up, it showed a standby light.

                I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                The screen seems to blackout and stay black, but with a flashlight I can see the display.

                With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                Assuming...
                ORIGINAL POWER SUPPLY BOARD
                7 Photos
                11-22-2024, 01:46 PM
              • Loading...
              • No more items.
              Working...