ps3 slim no power

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • tedtones2600
    Member
    • Mar 2011
    • 18
    #1

    ps3 slim no power

    need help while my ps3 is on trying to mod fan speed, ive shorted the brown and gray on fan wires, then suddenly it shuts down

    happening now just beep when press on power, fan doesnt spin

    ive tried replacing psu nothing happens also checked fuses on the board and there ok

    any ideas?

    thanks
    Tags: None
    • stj
      Great Sage 齊天大聖
      • Dec 2009
      • 31086
      • Albion
      #2
      Re: ps3 slim no power

      trace those wires back to the source

        Comment

        Previous template Next

        Related Topics

        Collapse
        • PantherDave
          Microsoft Surface Pro (5th gen) model 1796 - no power
          by PantherDave
          Hi all!

          I'm trying to troubleshoot a Microsoft Surface Pro (5th gen) model 1796 that won't power on. Motherboard model is M1007506-015. My priority is retrieving data, but the SSD is integrated so it looks like if I can't repair it it'll need to go to a data recovery company. I've done a little basic board repair before, but nothing this advanced until now. So please forgive my ignorance in advance. 😅

          I found the boardview for this laptop in the forums here, and am able to open it on my PC with FlexBV.
          https://www.badcaps.net/forum/troubl...-hardware-devi...
          05-29-2024, 02:01 PM
        • GLISIT
          Asus Probook P5440UF-XB74 power issue
          by GLISIT
          Hi all,

          TL;DR - this laptop is driving me nuts with the oddball power-related behaviors. Appreciate any insight you can provide!


          I'm experiencing a power issue on an Asus Probook P5440UF-XB74. Although I've worked with electronics and computers for decades, this is my first attempt at getting into motherboard-level component troubleshooting. Any help the community can provide is greatly appreciated!

          A few weeks ago I was using the laptop (on battery power) for a Zoom meeting. The battery was running very low (long meeting) but I wasn't worried about...
          01-16-2025, 02:29 PM
        • WVUfan
          PS5 EDM-033 One Beep,No Lights, No Power Troubleshooting Help
          by WVUfan
          hello. i've a ps5 edm-033 mobo w/ no power, lights, but one beep when power pressed. i've hooked to uArt and only error code is 80871001 (DDR4 No Power or Short Circuit). i have a donor board, same model, that does power up, fan spins, blue light, and beeps 3 times, then powers off. it has a botched HDMI port replacement job. so w/ the board i'm interested in, with the error 80871001, i was able to research and obtain voltages of the SSD PMIC. i've attached pictures of the provided diagram by DylanBBK (@d62 on Discord) and my voltages and picture of my board. my question is on my picture...
          08-11-2025, 01:12 PM
        • SoulFreeze
          Lenovo Slim Pro 7 14ARP8 83AX No Power
          by SoulFreeze
          Hello All, I have a Lenovo Slim Pro 7 14ARP8 83AX, Board No NB6369A_MB_V5

          Behavior - Pressing power button results in three second led blinks on the button,
          Connecting charger lights up orange as normally would while charging.
          Connecting charger without battery blinks orange.
          No fanspin.

          Tried flashing bios, no change.

          I inspected the board and found a burnt component on the USB / Power button daughter board. I assume the comonent was an esd protection diode as it was on the USB A port power rails. removed the component but still exhibits...
          05-01-2025, 09:04 PM
        • sam_sam_sam
          Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
          by sam_sam_sam
          I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

          One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
          03-31-2024, 02:12 PM
        • Loading...
        • No more items.
        Working...