Asrock K7S8X R3.0

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • larrymoencurly
    Badcaps Veteran
    • Oct 2004
    • 960
    • USA
    #21
    Re: Asrock K7S8X R3.0

    Originally posted by Scenic
    jamicon is crap IMHO..

    seen lots of them in really cheap DVD players...
    bulging or open of course..

    edit: i don't even know if they produce low-esr caps...!?
    most i've seen were GP caps..
    A couple of weeks ago, I replaced four bad Jamicons in the vertical output section of my 12-year-old Sanyo TV. Oddly, none of the Jamicons driven by the the horizontal output section were bad (ESR measured).

      Comment

      • andlcs
        Member
        • Feb 2007
        • 22
        #22
        Re: Asrock K7S8X R3.0

        I had a K7S8X-E R3.0 (it's the same PCB) with OST RLP capacitors instead of Taicon :]

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • Exim
            ASRock N100M, no picture no boot, but semi-alive
            by Exim
            Hi guys,
            I managed to semi-kill an ASRock N100M board after updating Bios from 1.10 to 2.01. It's a zombie now, dead, but not dead.

            ASRock N100M special features:
            - CPU soldered to board, small Intel 12th gen
            - iGPU
            - four POST LEDs

            Problem after updating Bios to 2.01 using the in-Bios update tool: no picture, no boot.
            I am not sure anymore if it booted at least once successfully after updating the bios to 2.01, maybe not, I can't remember. I think it did not.

            Symptoms:
            - no picture/signal on any of the display connectors,...
            board
            2 Photos
            04-01-2025, 02:36 PM
          • MasterCap
            What IC does AsRock usually use to make the PWM signals for GPU fans ?
            by MasterCap
            I have an AsRock Taichi 7900xtx, and the minimum fan speed is way too high at 1000rpm, and thats with it's Quiet BIOS switch on, and me setting the fan profile as low as it goes, while on.

            Now 1 thing I could do is just make some circuit to put in between the fan the the GPU, and leave the fan on all the time, but anytime the GPU is sending the PWM for min speed, I'll just send something lower and quieter.

            But does anyone know what how AsRock usually sends the PWM to the fans on GPUs and mobo's? Is it from the MCU that's often near the 12V inputs and fan jack ? Or is...
            12-28-2024, 08:42 AM
          • nolaryie
            BIOS .bin file for ASRock B450M Steel Legend
            by nolaryie
            Hi, I’m looking for a clean, working BIOS .bin dump (16MB) for the ASRock B450M Steel Legend motherboard.


            I’ve already tried flashing the official ASRock ROM file via CH341A, but it won’t post — I believe the capsule format is incompatible.


            Any BIOS version that supports Ryzen 5 2600 is fine (e.g., P2.30–P3.60).


            If anyone has a working board and can dump the BIOS using CH341A or flashrom, I would really appreciate your help.


            Thank you!
            08-06-2025, 12:01 PM
          • khanhtq0
            Full BIOS Dump for ASRock H310M-HDV Rev 1.02 (MX25L12873F)
            by khanhtq0
            Hello everyone,

            I'm looking for a full BIOS dump (.bin) for the ASRock H310M-HDV Rev 1.02 motherboard. The BIOS chip is a MX25L12873F (128Mb / 16MB).

            I’ve already tried flashing the official BIOS from ASRock (version 1.40 and 3.30), but those are Instant Flash versions and don’t include the full SPI image (e.g. Intel ME Region, Descriptor, etc.). After flashing, the board powers on only when I short PS-ON to ground, and it fails to generate Vcore and 2.5V. Other rails like 1.05V and RAM voltage are present.

            I suspect the original Intel ME and descriptor...
            08-06-2025, 02:14 AM
          • zklgfs
            AsRock B560 Pro4 Possible Short on +1.8VSB
            by zklgfs
            Hi,

            I have an AsRock B560 Pro4 (boardview: https://www.badcaps.net/forum/troubl...pro4-schematic) that's completely dead (it doesn't even turn on the power supply when the power button is pressed or the power button pins are shorted). I do get about 3.4V on the power button pin, but 1.8VSB isn't there. The resistance to ground on the inductor PL53 is only about 0.1-0.4 Ohms. Am I correct in assuming that there must be a short...
            06-07-2025, 02:22 AM
          • Loading...
          • No more items.
          Working...