FireGL V7300 7350 - repair

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • N²x²N
    Senior Member
    • Apr 2023
    • 54
    • Italy
    #1

    FireGL V7300 7350 - repair

    Hello!!

    I already posted in the schematics section but no go. Old card and thus to be expected.

    But I can try to ask here.


    In the pic you can see two components, one is missing and one is damaged.
    The damaged one the same as others that are already on the board:

    K1N sot-23, guessing it's https://pdf1.alldatasheet.net/datash...T3904-7-F.html

    The missing one is a capacitor, guessing it could be the same as some other around that area. Who knows for sure?

    The video card actually works, it POSTs and can go through all the way to Windows but I didn't want to stress it as it has missing components/damaged components and you can never know if it's going to puff its way out. After that you can "holy smoke" all the way you want but it won't bring it back.
    Attached Files
    Last edited by N²x²N; 06-07-2023, 09:12 AM.
    Tags: None
    • N²x²N
      Senior Member
      • Apr 2023
      • 54
      • Italy
      #2
      Re: FireGL V7300 7350 - repair

      Up

        Comment

        Previous template Next

        Related Topics

        Collapse
        • BMCappelletti
          Macbook Air A1466 EMC 3178 missing power and liquid damaged
          by BMCappelletti
          Hi everyone.
          Macbook Air A1466 EMC 3178 (board 820-00165 A) not turning on and no charging light. Completely dead. With no battery connected it would power up and I could hear the chime, but nothing on the screen and then a sudden turn off. Sometimes during the chime. Opened it up and found some liquid damage. The flat that connects both boards has damage in one side (with a missing pin already). The connectors on the boards are fine, though.
          Also, there was liquid damage on the included picture area, which are R8111 and C8111. A quick and soft brush on it made the resistor be gone....
          04-15-2024, 01:24 PM
        • ugamazing
          820-02020 PPBUS_AON missing
          by ugamazing
          Board had no history of liquid; unsure of drop history, but no signs of damage of any kind worth noting.

          Charger sitting at 5v/0a. PPBUS is at 1.9v-0.9v steady cycle (peaks, drains, loops). Confirmed CHGR_EN_MVR is missing, but DCIN was reaching ISL just fine, so replaced ISL--no change at all. Confirmed pp3v8_aon is also missing--and being unsure *exactly* which signal appears first (or if they are simultaneous), I inspected PMU/U8100 area and found no shorts, but also found PP3V8_AON_MPMU_ISNS_VIN missing (not shorted). Replaced U8100 just in case (have had them fail in weird ways),...
          02-05-2025, 04:21 PM
        • jpreza
          Apple NVIDIA AGP GeForce 6800 GT Dual Link DVI+DVI outputs 603-6338 missing caps!
          by jpreza
          Hi everyone,

          I recently acquired this card from a seller who was selling a PowerMac G5 for parts. He mentioned that the video card was probably broken too.

          Upon closer inspection, I can tell the reason why it won't work: it's missing a bunch of CAPS! (it's also missing an inductor - 1.0uH).

          It's a nice card as it's one of the few AGP cards that will support 2560 x 1600 resolution on a PowerMac G5 using a 30" Cinema Display.

          Looking at the card, it appears to be missing the following:

          1x 1.0uH inductor - orange square
          2x...
          1 Photo
          11-01-2024, 10:54 PM
        • gurj1979
          Asus Zenbook UX431DA / UM431D - Ryzen - missing PWM Fan Signal.
          by gurj1979
          Hey guys.

          Need help with this one.
          Fan not spinning due to missing PWN Fan signal.
          Also 5 seconds from powering up it freezes, unless in BIOS.
          But as soon as Windows starts to load, it will freeze.
          CPU is COLD / Room temp when it freezes.

          I've replaced the CPU, same problem.
          Replaced SIO/KBC IT8987e and reprogrammed - same problem.
          Replaced fan - same problem.
          Replaced flex cable from board to daughterboard (which has fan connector on it) - same problem.
          Checked the Thermal sensors around CPU and Board to the SIO/KBC and...
          08-19-2024, 05:22 PM
        • salopian
          Macbook Pro Retina 13” 820-3476-A (A1502) - missing PM_SLP_S4_L
          by salopian
          Hello. I would need some advice please.

          My son's MBP suddenly stopped working and is now only getting the green-then-orange light on Magsafe and no fan spin.
          He brought the MBP into the house (22 deg C) from a very cold conservatory (-3 deg C) and turned it on straight away. The Mac suddenly died a few minutes later.

          I examined the logic board and couldn't find any signs of water damage, corrosion, blown up components etc. Nothing was ever spilt on it, and the logic board looks immaculate.

          I have already replaced the logic board with another...
          02-27-2021, 07:30 AM
        • Loading...
        • No more items.
        Working...