ADSL Modem DSL-300G

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Decade
    Member
    • Dec 2005
    • 37
    #1

    ADSL Modem DSL-300G

    Lately I've been having a hard time to log on, no one in the neighbourhood had any problem so I decided that the fault was at my place.
    A quick check under the hood showed a bulged TEAPO35V/220uF replaced it and now I go faster than ever
    Attached Files
    Tags: None
    • willawake
      Super Modulator
      • Nov 2003
      • 8457
      • Greece
      #2
      Re: ADSL Modem DSL-300G

      good job! routers/modems are usually full of badcaps. not only that though their temperatures are incredibly high.
      capacitor lab yachtmati techmati

        Comment

        • Decade
          Member
          • Dec 2005
          • 37
          #3
          Re: ADSL Modem DSL-300G

          Thank's!
          Yes they are running real hot inside, there is not much air that pass inside the box, I think it is a common problem with D-link Friend of mine mounted a small fan on top of the cover and got rid of all problems their mains adapters are also prone to fail

            Comment

            • markiemrboo
              Member
              • Mar 2006
              • 44
              #4
              Re: ADSL Modem DSL-300G

              That's quite interesting! I think I might open my modem when my caps arrive and see if any in there need replacing or anything

                Comment

                • willawake
                  Super Modulator
                  • Nov 2003
                  • 8457
                  • Greece
                  #5
                  Re: ADSL Modem DSL-300G

                  it is no problem to recap if you find some bad ones. routers, switches etc, it is much easier than motherboards.
                  capacitor lab yachtmati techmati

                    Comment

                    • japlytic
                      Badcaps Legend
                      • Oct 2005
                      • 2086
                      • Australia
                      #6
                      Re: ADSL Modem DSL-300G

                      Our Billion ADSL Modem/Firewall Router contains Teapo SEK series and one Hermei HV series (3300uF 25V) unit; none of them were bulging since the modem was working for two years, despite running a bit hot.
                      My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.

                        Comment

                        • Decade
                          Member
                          • Dec 2005
                          • 37
                          #7
                          Re: ADSL Modem DSL-300G

                          No wonder they fail now and then these modemes run real hot.
                          Have looked in to several of D-links modems but this is actually the first time I've found a bulging cap, seems that better airflow cure many of their problems. Just by open the top cover of my D-link router all shut down problems in my network stopped

                            Comment

                            Previous template Next

                            Related Topics

                            Collapse
                            • dahm
                              tenda v12 ac1200 modem
                              by dahm
                              please need me tenda v12 ac1200 modem bios dump 8mb
                              05-23-2025, 12:15 PM
                            • rbvndonh
                              Lenovo T440s 1802 WWAN modem error
                              by rbvndonh
                              Hello,

                              I had factory installed Ericcson modem. It was working, but later was changed into Dell 4G modem. It was working good.
                              Now, after BIOS repair (to the same which was rapaired in past in this machine) it shows 1802 error.

                              Does somebody have whitelist or know how to correct it or proper no-1802 tool or solution for this board?

                              Thank you
                              12-04-2022, 01:09 PM
                            • playit
                              broadband ut300r2u modem,link light stays on forever
                              by playit
                              ut300r2u modem,link light stays on forever no matter if if dsl phone wire connected or not.i dint mess with any firmware ,it started to be like this for past few months until it stopped all together to work anymore,so learned that flashing might help, need dump file for this modem, i have only ch34a1 programmer.so i erased and flashed with few bin or ras files i got from internet but nothing worked.so further reading let me know that have to flash a whole full dump .if any idea, pls share, thank you.
                              08-11-2022, 01:44 AM
                            • TheQuentincc
                              Dell Precision 7710 no M.2 Wifi AND LTE modem
                              by TheQuentincc
                              Hi,
                              I have an issue with a 7710 motherboard, nor Wifi card/slot (8260AC and 3160AC) and LTE modem/slot (EM7455) are detected in bios/OS, the strange thing is that the wifi card is a wifi/bt combo and the BT is recognized in bios and working.
                              Since BT is working I think the power for these card is present, I already tried a few bios for the motherboard (asked on another thread) but only one is working, I got the board with a bricked bios and it's not a thunderbolt version.

                              I believe there is either a signal that disable the M.2 slot (all enabled in bios) or wireless...
                              07-29-2022, 01:40 AM
                            • Thunderace7
                              Cooker Hood Repair
                              by Thunderace7
                              Hi.
                              I've been repairing a cooker hood for my daughter and, although I have got it working, I am puzzled by a couple of things.
                              I have attached the circuit diagram I made from studying the PCB. It is a bit rudimentary but it served its purpose.
                              There is a buzzer, driven by output P0.0 of the processor, and the circuit seems to be a bit strange. The buzzer seems to be continually powered by 12 volts but is short circuited by the driver transistor. Any idea why this should be? I have checked the PCB several times and this is definitely how it is wired.
                              The second thing...
                              11-02-2023, 09:46 AM
                            • Loading...
                            • No more items.
                            Working...