Sharp Data Pro Projector (PG-D2500x) in Stand by

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • troxel
    Member
    • Jan 2013
    • 34
    • USA

    #1

    Sharp Data Pro Projector (PG-D2500x) in Stand by

    The projector was working fine and suddenly the next day would not work. The power light and lamp light blink green and the projectors sounds like it's starting up but then goes into standby mode. The lights blink many times, and eventually both will turn red.

    I have two projectors and switched the bulbs around and get the same problem. (The donor projector works fine with the other bulb, so I believe that would rule out the lamp?).

    Any help or suggestions would greatly be appreciated.

    Thanks!

Related Topics

Collapse

  • vestaviascott
    Epson 5040UB Projector No Lamp Strike Stuck in Startup - Blinking Status/Lamp Lights
    by vestaviascott
    Hoping someone here can put me on the right track. I'm trying to troubleshoot/flowchart the "internal projector error" on my newly acquired Facebook Marketplace bought Epson 5040UB projector (3LED, not DLP). Owner said it needed new lamp, actually error code blink pattern indicates "Internal Projector Error, call Epson support". Unit is out of warranty as of 8/19

    Here's what happens:

    1) Power on
    2) Blue power indicator lights and the lens cover motor opens the lens cover, light fan noise heard
    3) Blue status light flashes for appx 4 minutes...
    07-29-2020, 06:08 AM
  • Eric D.
    Sharp LC-60LE810UN Lamp error
    by Eric D.
    Hello everyone!
    I just acquired a Sharp Aquos for free.
    When I plug it in, it will try to power on, but it fails.
    The "error code" is 1 long flash, then 1 short flash, which suggests it is a lamp error code, according to the manuals.
    I did a bit of research and did what I found could be the possible issues;
    I removed the back panel, checked for continuity on both fuses where the power cable connects, and I get somewhere around 0.05. That should be good.
    I also tested the leads going into the psu board from the wall connector; I get 120V.
    I disconnected...
    01-18-2025, 05:14 PM
  • platinumsteel
    Epson VS250 Projector Lamp Not Working.
    by platinumsteel
    Hi guys gooday i have a Epson VS250 Projector that turns on and is also being recognized and detected by the computer when i plug the hdmi cable.The only issue the projector lamp is not working .Are these lamps repairable ? Or i should just forget repairing the lamp and just buy a replacement. Thanks...
    04-09-2023, 04:03 PM
  • Yanleb
    Sharp LC-60LE810UN Lamp Error
    by Yanleb
    Hi all,

    I have this Sharp LC-60LE810UN that stays off and blinks a Lamp Error (1 long flash followed by a short flash, in a loop).

    I already confirmed that the first backlight strip has an open LED using a LED strip tester. The other 3 LED strips are fine.

    Before tearing the LCD panel apart, I want to make sure that the rest of the TV set is good. I've tested the power-supply/LED inverter board by sending 5 volt to PS-ON, to PNL-POW (that commands power the T-CON board only), OFL and STB pins. The power-supply is good.

    I've tried all the key...
    08-24-2021, 11:48 PM
  • Document Archive
    Lenovo ThinkPad P51s + ThinkPad Stack Mobile Projector Mobile workstation P Specification for Upgrade or Repair
    by Document Archive
    This specification for the Lenovo ThinkPad P51s + ThinkPad Stack Mobile Projector Mobile workstation can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the P51s + ThinkPad Stack Mobile Projector boardview and P51s + ThinkPad Stack Mobile Projector schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum....
    09-06-2024, 06:11 AM
  • Loading...
  • No more items.
Working...