Harman Kardon AVR 130 receiver capacitor replace 50v to 63v?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • basskilla
    Member
    • Mar 2014
    • 18
    • Hungary
    #1

    Harman Kardon AVR 130 receiver capacitor replace 50v to 63v?

    Hi there!

    I have a Harman Kardon AVR 130 receiver,seems capacitors died,
    Can I replace the 6800uf 50v capacitors to 6800uf 63v?
    The local shop have only 6800uf 63v.

    Thank You for the reply and help!

    Best wishes!

    Lac
    Tags: None
    • goodpsusearch
      Badcaps Legend
      • Oct 2009
      • 2850
      • Greece
      #2
      Re: Harman Kardon AVR 130 receiver capacitor replace 50v to 63v?

      Of course. The voltage rating is the maximum voltage the cap can see in its legs.

      So a capacitor rated for 63V could work without issues with lower voltages than 63V.

        Comment

        • basskilla
          Member
          • Mar 2014
          • 18
          • Hungary
          #3
          Re: Harman Kardon AVR 130 receiver capacitor replace 50v to 63v?

          Ok,thank You for the info!

          Best wishes!

            Comment

            Previous template Next

            Related Topics

            Collapse
            • funky2x
              Harman kardon onyx studio 7 Smd code
              by funky2x
              Cant find what smd code Y0DVA.
              sitting in Harman kardon onyx studio 7. Appreciate any help.
              1 Photo
              05-29-2025, 03:44 PM
            • PowellSkier
              Cement resistor swap in Harman Kardon AVR
              by PowellSkier
              Would I be able to swap a 0.27 Ohm Kx2 5W resistor for a 0.22 Ohm Jx2 5W resistor in a Harman/Kardon AVR? Cement type.
              06-04-2024, 06:41 PM
            • PowellSkier
              Harman/Kardon AVR 645 returning to stand-by after a few seconds.
              by PowellSkier
              A Harman/Kardon AVR 645 repair has been a hobby of mine for the past several years. My latest attempt involved the purchase of a DOA unit for part swapping and testing. The original AVR would power up then shut down after a few seconds. I completely tore down both units, found a couple of bad components and reassembled one of them. Same issue, no speakers connected. After extensive research I found a repair document from Harman/Kardon that explains the protection circuit in fantastic detail and provides specific test points for each fault (power, DC detection, overload & power) and the voltage...
              06-17-2024, 11:43 AM
            • falafinasul
              Harman Kardon AVR 3700 Fonte queimada
              by falafinasul
              Harman Kardon AVR 3700 burned, it does not turn on and I have already changed the fuse and when turned on it burns again. It must be shorted.

              I made a new Diagnostic and verified that the input source is shorted.

              Someone help
              02-24-2023, 05:51 PM
            • BlackScreen_22
              Harman Kardon sub TS11 (ds15 amplifer) blows fuse and mosfets
              by BlackScreen_22
              Hi, I'll start by saying that I'm not an expert and I've reached a point where I don't know what to try/do anymore...
              Starting from the beginning: I opened this subwoofer for the first time with a very strong smell of burnt electrical components, I realize that on the amplifier board there is a hole between V+ OUT and GND about the size of a finger, the damaged components were the shorted mosfets, two damaged zener diodes and two capacitors. I bought everything, I fixed the hole by cutting the pcb and putting a piece of a perforated board.
              I had no problems connecting mosfets and capacitors,...
              08-27-2024, 12:46 PM
            • Loading...
            • No more items.
            Working...