Repair of Icom Microphones

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Jack Crow
    It's a CLASOB!
    • May 2008
    • 823
    • USA
    #1

    Repair of Icom Microphones

    Hi all,
    A while back I did a photo article for some ham radio friends on how to fix up failed microphones on ICOM radios.

    This is the link.

    http://www.flickr.com/photos/9010884...7622973054587/

    Hope it helps.

    Jack Crow
    "You are, what you do, when it counts"
    The Masso

    "Gravity, the quickest way down"
    Mayor John Almafi

    "You ever drop an egg, and on the floor you see it break?
    You go and get a mop so you can clean up your mistake.
    But did you ever stop to ponder why we know it's true?
    If you drop a broken egg you will not get an egg that's new?"

    MC Hawking
    Tags: None
    • kc8adu
      Super Moderator
      • Nov 2003
      • 8832
      • U.S.A!
      #2
      Re: Repair of Icom Microphones

      the hm-56a is known for sm caps leaking too.
      got an ic-2410h free because of this.oh and the display bulbs were out.a few sm tantalums and 6 3mm white leds =1 good 2m/70cm rig.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • alberto79
          Icom PS-15 power supply
          by alberto79
          Hi!
          I have an old (but good) Icom PS-15 power supply.
          This PSU was modified by a technical and now the original control circuit is no longer there.
          I want to make the original circuit because the modified circuit don't work fine.

          The original circuit use an old components and i need help to find (if possible) equivalent (but modern) components.

          The first components is U05, rectifier/filter.
          The second is XZ-051, reference voltage.






          Thank you for help.

          Alberto...
          04-19-2021, 08:38 AM
        • stj
          Motorola DMR radios
          by stj
          anybody know about programming them?
          09-07-2022, 12:03 PM
        • Comp_Pro
          820-02020 No Display, No TPAD, No USB, No KB, Fast Fan Spin
          by Comp_Pro
          Hello All,

          This is a weird one. This M1 Macbook Pro was brought in for liquid damage. Customer was getting video only on external monitor. Most liquid damage was located around the backlight circuitry, namely the backlight capacitor bank. It was not too severe. Ultrasonic cleaned and about 3 corroded capacitors replaced. FP800 backlight fuse was also blown. Nothing down the line from the fuse is shorted. May have blown this fuse from overload during liquid being present.

          Also had to repair area of QD530 which is PBUS VOLTAGE SENSE. Repaired traces to RD531 and RD532...
          05-10-2023, 02:26 PM
        • dicky96
          Wireless Microphones - what test gear can I use to diagnose?
          by dicky96
          I'm getting asked mote and more often to look at faulty Wireless microphones.

          I've already got several lying around at the workshop I don't know what to do with and I've been asked to look at two more in the last week alone!

          There seem to be a mix of UHF and VHF ones.

          Problem is I don't know how to go about diagnosing the faults. I have all the usual test gear for repair work , various meters and scopes etc.... but I can't even figure out the basics like how to determine whether the microphone is actually transmitting or if the receiver is not receiving....
          03-15-2019, 05:20 PM
        • ductranvinh
          Graphics card repair, Basic Measurements
          by ductranvinh
          Hi everyone!
          The preface to this article is for those who are new to graphics card repair. I'm not as talented as mods or admins either.
          But in this article, I will guide you through the most basic things to quickly recognize the disease in each block, so that you can make a foundation as well as form a habit.

          Note! This article may or may not be true.

          Measurement: (must have boardview of course)
          Adjust the impedance scale

          12v block
          Measure the 12v fuses, see if they burn out.
          If the fuse blows, the risk of burning the pcb is...
          06-29-2022, 05:12 PM
        • Loading...
        • No more items.
        Working...