Onkyo TX-NR616, constantly clicking, no display, no light/led

[R_J]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

How did you try and update it via usb if you don't have the firmware? Download it from Oink-yo

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

try using a USB stick to update as opposed to a network connection.

Hi

All

I have tried to update by USB and still get the same error

5-82 on vsp and vmpu



Please can someone send me the firmware so that I can program this myself or upload it

alternatively can I use the UART cable

Please can someone reply and assist me, I will be really grateful and appreciate it so much



Many Thanks

Kind Regards

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

Hey all

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

This is what i get when i check the firmware
any help appreciated please

I have tried to do update by using the ethernet cable
When i try to do them individually using the menu
it gives the following error
error!! 5-82

on vsp and vmpu
not tried by usb

I have a a uart cable and a USB CH341A chip programmer
Many Thanks all in advance
Please help

[budwich]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

try using a USB stick to update as opposed to a network connection.

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

Hi
I have got My Onkyo Tx-NR616 to turn on but there is no HDMI OUT displaying on the TV
I have gone through debug mode and the firmware check
V and K shows no firmware details

I have tried doing the firmware update using the key combination and using the ethernet cable but get error
"error!! 5-82"

Is there any way to force the firmware update please
Or using the uart interface

I am really stuck and need some help
Thanks all in advance

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

First use your meter to check for continuity from the fuse to ground otherwise it might just blow again.

I checked that and Will recheck again
Will report back
Thanks all

[mmartell]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

First use your meter to check for continuity from the fuse to ground otherwise it might just blow again.

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

Look at the schematic and you will see what it is for, This is the +12VD(ANA), +12TRG and the POFF2, it is not the same 12 volts that supplies the relay.

Thanks. Yes I saw that. Was trying to post a reply but wouldn't post. Thanks. Will put a replacement fuse

[R_J]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

Look at the schematic and you will see what it is for, This is the +12VD(ANA), +12TRG and the POFF2, it is not the same 12 volts that supplies the relay.

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

That fuse is in the a/c input for D201 bridge rectifier that supplies +12volts to the hdmi board. It also supplies a voltage via D204 to the POFF2 line on P2800A which connects to Main Micom Q7009

Thanks for the reply
Can this fuse stop the unit on turning on and causing the relay to constantly click as it is

I measured and i had 12v on pin 1 and pin 4 on jl901b
maybe this was not enough to turn the receiver on

I will appreciate all your help please

Thanks again

[R_J]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

That fuse is in the a/c input for D201 bridge rectifier that supplies +12volts to the hdmi board. It also supplies a voltage via D204 to the POFF2 line on P2800A which connects to Main Micom Q7009

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

After some probing and testing resistors
I came across F201, that shows no continuity.

I am not sure how this has blown, there are no marks or anything
Would this cause for it not to turn on

Please someone help
Thanks all in advance

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

I have been doing more voltage measurements. The results are below

I tested q7018

pin 1 is gnd,
pin 2 is 4.8v
pin 3 is 3.3v

also tested q7019

pin 1 is gnd,
pin 2 is 11.89v - 11.90v
pin 3 is 5.6v

Nothing is getting hot and i cant see any bulging caps

Please will really appreciate all the help from this forum
Many Thanks in advance

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

The relay is working
i have tested by jumping the wire pin 1 and pin 3
there is a strong latch

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

Thanks for the reply
Where do i start looking
on the power supply board or the hdmi board
I have not worked on such amplifiers before so any help will really be much appreciated


If there are any onkyo experts, please reply
Thanks so much

[ReeceyBurger123]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

I’d start looking for anything shorted first just anything you can, relays don’t just click on and off like that unless there’s something wrong.

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

I have put all the screw back for the power supply board that secures it to the chassis and I put two screws securing the hdmi board to the chassis*

I tested ground from pin 3 from jl901b to the chassis and it was a good ground. Near to the same as when I touch my meter probes together.*
I get voltage on the cable coming from the power supply* board that connects to the hdmi board*
Below are measurements taken from when the cable is plugged into the hdmi board*
Pin 1 is 12v but when relay clicks it goes down*
Pin 2 is 0v
Pin 3 is GND*
Pin 4 is 12 v
Pin 5 is 0v

I read that if I put jumper wire from Pin 1 and Pin 3 on jl901b which is on the hdmi board the relay should latch but with the transformer cable removed*I tried this and got nothing*
I tested the relay and got about 300 ohms*And the relay is clicking*
I am really stuck and will appreciate some detailed help from this amazing community Please*

Many Thanks*

[lcdcaps1]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

try and see

Have you had similar issues in the past

[petehall347]

Re: Onkyo TX-NR616, constantly clicking, no display, no light/led

try and see