Yamaha HTR-5630RDS AMP sitting down

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • roadrash
    Badcaps Veteran
    • Oct 2015
    • 493
    • U.K.
    #1

    Yamaha HTR-5630RDS AMP sitting down

    I wonder if anyone has any idea what could be causing this to shut down. When you turn it on you hear the relay click and it all lights up. Then about 4-5 seconds later the relay clicks again and it turns off. I have looked carefully at it and checked all connections and it all seems ok.
    Anyone have a suggestion?
    Attached Files

    if you find these attachements useful please consider making a small donation to the site

    Tags: None
    • stj
      Great Sage 齊天大聖
      • Dec 2009
      • 31291
      • Albion
      #2
      Re: Yamaha HTR-5630RDS AMP sitting down

      that type of construction is just begging for cracked solder joints!

        Comment

        Previous template Next

        Related Topics

        Collapse
        • CoinCoin88
          Garage door RX unit (Cardin S38C) does not short relay to send opening signal
          by CoinCoin88
          Hello everyone,

          I'm turning to the Badcaps community to help me troubleshoot the radio Rx card from my (old) garage door opener. While I could just ditch that card and replace the whole system, I first would like to understand "why" it suddenly stopped working, because that's just how I am wired...!

          Some basics: the receiver works on a 30.875 Mhz frequency. Yes, I'm aware this is not in use anymore in a looot of places. It does not use any rolling code, it's just a regular dip-switch code that you have to set up on both the receiver and transmitter. The receiver...
          09-15-2025, 03:36 AM
        • jm1234
          9V relay temperature 40C
          by jm1234
          Hi, I'm seeing one 9V relay having temperature 40C on its 9V (primary) side. Does that seem right? I switched 2 relays on that board and the temperature was the same (on the same position), so I'm sure it's not a faulty relay. I measured voltage on that relay and it was 9.5V DC, so that looks good. I don't see any other relay on that board having that kind of temperature and they have 9V on them too.
          I thought maybe the transistor that is switching this relay keeps switching on/off, so I also checked for AC and there was almost none: 0.3V using mV range. No steady frequency was shown, but...
          05-09-2024, 03:03 AM
        • edugimeno
          Biomass Boiler not driving cleaner motor relay. ENERTRES BIOMASA BI-650
          by edugimeno
          Hi everyone!
          I have this board that suddenly stopped supplying power to an output that drives an interchanger cleaner motor.
          I checked while the board was in place with all wires attached and there's no AC voltage on the corresponding plug X5
          This X5 is driven by fuse F8 (tested OK) which comes from the second orange relay
          To make sure there are no charcoaled contacts inside the relay, I got a 24VDC power supply and got it ready to manually power up the coil side of these relays.
          I respected the polarity, positive to cathode of protecting diode
          So provided all...
          04-18-2024, 01:15 PM
        • sam_sam_sam
          Mitsubishi CNC switching power supply board dead / relay board bad diode failure
          by sam_sam_sam
          I was working on this CNC machine today found no keyboard functioning no control relay powering on
          The screen powered on and was giving an operation error but the manual was not very clear about what the error exactly was but with a little bit of troubleshooting and finding out that the control relays not powering on and no keyboard functions we narrowed down to this one switching power supply which of course does not have any indicator LED light they are on the keyboard interface/relay controller board

          Found shorted diodes on main controller relays there are 3 of them that...
          01-07-2023, 05:43 PM
        • sanalelevenstar
          Yamaha RX-V485 Wn9711 Update
          by sanalelevenstar
          Help Needed: Yamaha RX-V485 Network Issue After Firmware Update (WN9711 Error)

          Hi everyone,

          I'm facing an issue with my Yamaha RX-V485 receiver. During a firmware update, the process failed, and now the USB, Bluetooth, and network functionalities are not working. Occasionally, the receiver displays the error code WN9711.

          I came across Yamaha Technical Bulletin No. 0103, which describes a similar issue for models like the RX-V4A, RX-V6A, and RX-A2A. According to the bulletin, the issue can be resolved by shorting soldering points (e.g., J260 for RX-V4A or...
          12-04-2024, 04:32 AM
        • Loading...
        • No more items.
        Working...