Diall IP54 AE0295 LED Rechartgeable lamp

6BW6

Senior Member

Join Date: Jan 2015

Posts: 55

Country: UK
#1

Diall IP54 AE0295 LED Rechartgeable lamp

03-12-2021, 07:21 AM

I've been given a Diall IP54 AE0295 LED Rechargeable lamp the only thing not working is there is no 'charge voltage' from the buck regulator on the LED control board.

The charger delivers 24VC DC and the LED indicators and LED lamp works. The circuit board is marked AE0195-BAT. The buck regulator uses a 8 pin SMD chip and there's is nothing coming out of it.

The only thing I can make of the marking is either XL40 or X140, by chance does anyone have any clue what chip it is..... must put out around 7.4V or so because this is the Lithium battery voltage.

Thanks, Dave

Last edited by 6BW6; 03-12-2021, 07:25 AM.
Tags: None
6BW6

Senior Member

Join Date: Jan 2015

Posts: 55

Country: UK
#2

03-12-2021, 09:12 AM

Re: Diall IP54 AE0295 LED Rechartgeable lamp

Eureka....
The buck regulator chip is a XLSemi 'XL4201' is the type number, here's the data sheet-:

Answered my own question.... might be useful to someone out there.

Dave

Last edited by 6BW6; 03-12-2021, 09:12 AM. Reason: gotta learn how to spell
Comment

Previous template Next

Reolink RLC-410-5MP - buck convertor

by jm1234

Hi,
it's a PoE camera and it stopped working. Using thermal image I identified failing component U22 marked as 16AF which seems to be buck convertor TI https://www.alldatasheet.net/datashe...62569DBVR.html. I took it out and It is inteed shorted on the output. However, after I took it out, the resistance between the output pads (on the board) still shows 190ohm, is that bit low?
Another issue is, seems to me I must be missing one of the tiny resistors R810 that should make up the voltage devider for the buck convertor. Honestly I did this months ago, I cannot...
- Channel: Troubleshooting Printers, Copiers, Scanners and other Imaging & Printing Devices
07-14-2025, 04:30 AM
Protecting against over volts when fitting a buck regulator controller. Good Idea?

by dicky96

Hi guys
Here is a general question and I would like to hear your thoughts on it

I've just replaced a very small 11 contact MP2329 QFN on a motherboard

This supplies 1.8V STBY to the PCH - but the faulty one was only giving 0.7V

Anyway I fitted it, but it is very close to the DIMM sockets and I can not clearly see down one side of it to make sure it has soldered properly ,even shining a torch down there. The other sides look OK under the microscope and also in a jewellers loop. This is the side that has two resistors that set the output voltage
...
- Channel: General Electronics Technical Discussion
04-30-2021, 07:37 AM
HP 2311 display, 3.3v regulator fried, need help to replace

by disorder

hello,

i have a hp display 2311 to repair, totaly dead
on the board, il have 2 capacitor 470µf that are dead and the 3.3v regulator : ax6630-33
i have no such regulator, can i replace this one with a mic5209-33 (3.3v outpout regulator too) ?

thank you
- Channel: Troubleshooting Computer Displays
07-27-2025, 04:34 AM
Hisee CCTV monitor Buck regulator chip ID help required.

by zen

Hi all, won't go into details but managed to cook it myself.

Has two sets of codes on it.

Top code JWN8T

Just below code 2GL 4B

PCB code ZM11E-T30 V2.1

Out of a Hiseen CCTV monitor with no model of course....
- Channel: Troubleshooting Computer Displays
10-06-2022, 05:17 AM
Epson 5040UB Projector No Lamp Strike Stuck in Startup - Blinking Status/Lamp Lights

by vestaviascott

Hoping someone here can put me on the right track. I'm trying to troubleshoot/flowchart the "internal projector error" on my newly acquired Facebook Marketplace bought Epson 5040UB projector (3LED, not DLP). Owner said it needed new lamp, actually error code blink pattern indicates "Internal Projector Error, call Epson support". Unit is out of warranty as of 8/19

Here's what happens:

1) Power on
2) Blue power indicator lights and the lens cover motor opens the lens cover, light fan noise heard
3) Blue status light flashes for appx 4 minutes...
- Channel: Troubleshooting TVs and Video Sources
07-29-2020, 06:08 AM
Loading...
No more items.

Diall IP54 AE0295 LED Rechartgeable lamp

Diall IP54 AE0295 LED Rechartgeable lamp

Comment

Related Topics