Triac BT136 pin-out on PCB

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • jh20
    Member
    • Jul 2012
    • 27
    • australia
    #21
    Re: Triac BT136 pin-out on PCB

    Just to update that the lamp is working again after replacing the triac and the resistor. Sorry for the delays...

      Comment

      • Agent24
        I see dead caps
        • Oct 2007
        • 4913
        • New Zealand
        #22
        Re: Triac BT136 pin-out on PCB

        Glad to hear you got it working!
        "Tantalum for the brave, Solid Aluminium for the wise, Wet Electrolytic for the adventurous"
        -David VanHorn

          Comment

          • SistMaticZ
            Senior Member
            • Jul 2019
            • 72
            • Morocco
            #23
            Re: Triac BT136 pin-out on PCB

            his one was easy. congratulations OP.

              Comment

              Previous 1 2 template Next

              Related Topics

              Collapse
              • Lvsitano
                Asus X532FL 3.2V at source and gate
                by Lvsitano
                I am having some trouble with troubleshooting a Asus X532FL rev 2.0 motherboard, which does not power on. So at the first MOSFET, I am getting 19V at the drain, and then 3.2V on both gate and source (compared with ground). Of course, the 2nd MOSFET's source will have 3.2v at source.

                First MOSFET is a QM3056M6 and 2nd MOSFET is a QM0930M3

                I already checked first MOSFET and source and gate are not shorted (drain with source not shorted either). Also I have 1.7V at the LDO rail (measured at the keyboard connector, as the power button is on the keyboard).

                First...
                06-26-2024, 02:13 PM
              • прямо
                TRIAC circuit
                by прямо
                Anyone is familiar with a TRIAC circuit?

                I came across this schematic, and I built it, but I can't seem to figure it out why I'm getting a low AC voltage output at the TRIAC terminals.

                With 230V AC hot side at the TRIAC MT2, I measured 60V AC between MT1 and neutral side when the comparator output LED indicator is on, and 20V AC when it is off.

                Same result if 230V AC hot side is at MT1, and I measured between MT2 and neutral side.

                My heating element doesn't work with 60V AC. It's not even getting hot and the thermocouple amplifier output is a...
                1 Photo
                04-27-2024, 02:12 AM
              • Nevillet
                Identifying a 'FS45' SOT23 device
                by Nevillet
                Hi All,

                I'm trying to repair a PCB that has some surface mount SOT23 devices that apear to be transistors but testing them on the board are giving confusing results.

                Its named FS45 but I can't find a datasheet that seems correct.

                The device is used in 10 places on the PCB. In 4 cases they appear to be controling triacs and the attached picture it shows it connected to a BT136 triac with the FS45 connected to the gate leg of the BT136.

                Can anyone identify the device and suggest an alternative?

                Many thanks.

                PS: I have...
                5 Photos
                06-19-2024, 11:42 AM
              • pickledegg
                Dell Inspiron 7501 / Vostro 7500 (2020) - eDP connector pinout/panel compatibility question
                by pickledegg
                Hello. I have an Inspiron 7501 here, it's the same as a Vostro 7500 in some markets (no clue). I was looking to replace the LCD, the panels included with these models are terrible.

                I have the schematic and it is a 4 lane eDP port on the board but the pinout seems quite weird, my question is if anyone recognises this weird pinout and knows of any other Dell models that may use it or even any compatible panel models. I have the 40-40pin cable that was used for the models with touch but do not need touch capability, was just looking for a better quality screen and higher refresh to actually...
                10-02-2024, 04:54 PM
              • maleksa
                Korg Kross2 Service Manual and LCD pinout
                by maleksa
                The LCD on my Korg KROSS2 keyboard is cracked and needs to be replaced.

                However, the cost of a replacement LCD is almost the same as the price of a second hand Korg KROSS!

                Does anyone have a copy of Korg KROSS2 Service Manual? I want to see the PINOUT for the LCD connection. Perhaps I can find a compatible LCD screen and not have to spend a fortune on an original replacement LCD.

                From what I can gather, the LCD screen is a COG with serial interface (SPI). Is there any way I can ascertain (perhaps with the use of a multimeter or oscilloscope) the PINOUT by...
                10-11-2024, 05:54 AM
              • Loading...
              • No more items.
              Working...