iPhone backlight circuit operation question

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • caphair
    started a topic iPhone backlight circuit operation question

    iPhone backlight circuit operation question

    Im curious why there are two different coils used. Is it for providing smooth current output or is a feedback system?
    Attached Files
    Last edited by caphair; 04-05-2017, 07:05 PM.

Related Topics

Collapse

  • gizmo1990
    What is this PSW1 part on a circuit board? Trying to fix a Canopus ADVC-300 DV/VHS Converter
    by gizmo1990
    I'm trying to fix this Canopus converter so that I can convert lots of old VHS cassettes. The problem is that it turns on for a split (and I mean split!) second, the fan jerks and then.. nothing. I've checked the power brick works. I've opened up the converter itself and been testing for shorts.



    The image attached shows the on/off switch (which I've checked works) to the left of the yellow socket. Below the yellow socket is a green block marked 26 with a strange symbol at the front. Putting my probes either end of this block, on the silver parts, gives an open short...
    10-21-2024, 08:02 AM
  • triplefour
    UN65TU700DF picture and sound but no backlight. BL tests ok but repl. PSU didnt fix!
    by triplefour
    this tv is throwing me for a loop. do samsung tvs no longer have the backlight self test feature built into the power supply?
    i tested the backlight with my LED tester and it lights up both strips. one of them reads 100v and the other reads 63.7v.
    unplugged mainboard from power supply but left backlight plugged in, and then plugged psu wall power in. expected to see backlights light up but see nothing.
    according to how ive diagnosed in the past, this would almost always be a bad power supply. replacement power supply was cheap like 20$ from ebay. but still i get not even...
    09-13-2023, 10:43 PM
  • Comp_Pro
    No Backlight Macbook A1990 820-01041
    by Comp_Pro
    Hello all,

    Am trying to figure out this backlight issue with this A1990 Macbook Pro.

    Tests performed:

    There is no backlight even with a good screen.
    Backlight IC is receiving the correct support voltages.
    Fuse F8400 ok
    Current sense resistor R8400 ok
    Backlight IC is receiving 3.3V on enable pin.
    Backlight IC receiving voltage from PPBUS_G3H, aprox 12.5V.
    Backlight IC receiving 5V from PP5V_G3S
    Backlight IC BKLT_SCL and BKLT_SDA both measure 0.545V diode mode to ground
    I2C_BKLT_SCL and I2C_BKLT_SDA both measure...
    05-06-2024, 10:23 PM
  • redbaron1007
    Yamaha HTR-3065 No power/No Standby
    by redbaron1007
    I got a Yamaha HTR-3065 on the bench currently that's got a no power/ no standby issue.When I plug it in it draws 0.01A from the wall, the relay for the ac transformer never clicks, there are no standby lights on the front, and pressing the power button does nothing. The fuse was not blown but upon measuring the voltages on the power low voltage power supply board (labeled operation 3 pg 89 in the schematic) they do not match what the schematic says they should be.
    S9 13.7V

    Pwr Ry 0V
    AC Det 9.1V
    Mgnd 0V GND

    The two pins on the transformer for the operation...
    09-12-2024, 03:04 PM
  • phuzzyday
    My horror movie continues.. "70X690E Power Supply- the Sequel - Attack of the Backlight circuit!"
    by phuzzyday
    This was my initial thread.. https://www.badcaps.net/forum/troubl...-m-at-wits-end

    (All the Electrolytics are brand new.)

    I started a new one, hope that's ok, because my question is different now! (Strangely enough, after I walked away for a few weeks, it stopped lighting up at all!!)
    I am determined to fix this power supply because I have the skills to replace bad components, I just need to find out...
    05-30-2025, 05:20 PM
  • Loading...
  • No more items.
Working...