Timer IC

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • barry wilkins
    Senior Member
    • Aug 2009
    • 172
    #1

    Timer IC

    I posted this a few weeks ago.
    I bought a 4047 IC from Maplin ,this is quite easy to drive a pair of Fets to make an inverter.
    I found eventualy the IC I first saw its IR2151 ,4 pins and Q & Q bar outputs to drive a pair of Fets.
    I have an inverter runing at the moment driving 2 12" flourescent tubes (26W)
    draws about 1 amp. What is nice is you have the frequency under your control.
    Tags: None
    • ben7
      Capaholic
      • Jan 2011
      • 4059
      • USA
      #2
      Re: Timer IC

      General, is there a problem?
      Muh-soggy-knee

        Comment

        Previous template Next

        Related Topics

        Collapse
        • DeanWy
          WD Sentinel DS5100 (NAS) boot issues
          by DeanWy
          Hi all,

          I have a Western Digital Sentinel DS5100 NAS system which has stopped working. It has dual BIOS. I bought the system second hand with an already broken primary BIOS (it rebooted multiple times until second BIOS was used).

          It worked until recently. The system was idle in Windows Server 2012 and a BSOD occurred, I think it was 'critical process died'. Thereafter it didn't boot, it just sat there with no video output and fan speed at 100% (there's a proprietary Windows driver by WD which controls the fan, outside of that it always runs at 100%).

          There...
          07-30-2024, 04:13 AM
        • Storyteller12
          Need help picking 12v timer!!
          by Storyteller12
          I need a 12v timer that cuts on when 12v applied (when door is opened) and cuts off after 2 minutes even if he door stays open with the 12v trigger. And resets when door is closed.

          The ones I see tend to start the timer when powered down. (Momentary switch)

          Thanks in advance
          09-05-2022, 07:24 AM
        • repair-it
          TOSHIBA DLP 52HM95 How to reset timer module on bulb
          by repair-it
          I replaced the bulb only on my Toshiba DLP The bulb is a TB-25. This is the first time I've done a bulb only replacement. Supposedly there is a timer module that needs to be re-calibrated or reset. I don't know where the module is located. I see some vendors selling the bulb with the housing stating module included which leads me to think the module is located inside the enclosure the bulb mounts in, but I didn't see it. Maybe it's inside the plug attached to the bulb?

          Anyway - I am seeking information on how to reset this so called module so that the lamp will operate. Apparently...
          10-11-2023, 07:18 PM
        • modd1uk
          Dell 5420 - First timer, messed it up, need help please.
          by modd1uk
          Hi guys

          Its my own fault, I'm just hoping somebody can help and the laptop isn't bricked.

          The BIOS chip is a 25rh256cxiq, I read it using neoprogrammer 2.2.0.10 but like a complete idiot didn't search the chip, it was set to the wrong chip, I read the BIOS, unlocked it, flashed the unlocked file and now the laptop is dead, won't even try to power on, only after I'd flashed it I realised the wrong chip was selected.

          How stuffed am I? Is there a way to flash a generic Dell Latitude 5420 BIOS so I'm not stuck with a dead paper weight?

          I have another...
          03-22-2025, 03:24 PM
        • JayPoorJay
          Hot Water Rad - A Few ECU Fans and a Timer Switch
          by JayPoorJay
          Good Afternoon, Good People.

          I know this will be an elementary little project for most if not all of you, but I thought I would write a post and get put on track, rather than bumbling my way through it with all kinds of trials and errors.

          I REALLY would appreciate y'alls help.

          This is the problem - My wife and I purchased a big ol Victorian/Colonial House in NYC two years ago. The kitchen is surrounded on 3 sides by exterior walls, there is also a 1/4 of the kitchen floor (ceramic tiles) that has a crawl space underneath, and the kitchen gets FREEZING cold...
          10-29-2024, 12:54 PM
        • Loading...
        • No more items.
        Working...