BenQ DV3250 Backlight flash then blackout

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Bill Lee
    New Member
    • Nov 2010
    • 9
    #1

    BenQ DV3250 Backlight flash then blackout

    My LCD Tv BenQ DV3250 backlight off after flash / sometimes on for few seconds. On signal is good, voltages measured as attachment. Wait for yours advises and tips. By the way, could you show me which part section is the feedback section? One more check, I can see a little image at the display when I give a strong light through it.
    Attached Files
    Last edited by Bill Lee; 11-11-2010, 10:13 PM.
    Tags: None
    • Toasty
      Badcaps Legend
      • Jul 2007
      • 4171
      #2
      Re: BenQ DV3250 Backlight flash then blackout

      This looks like just the power supply...

      Where is the inverter board - the one the backlight tubes are hooked to?


      Toast
      veritas odium parit

        Comment

        Previous template Next

        Related Topics

        Collapse
        • triplefour
          TCL 75S421 has sound but no backlight not even a flash
          by triplefour
          TCL 75S421
          PSU BOARD: 40-L402H8-PWD1CG
          it shows not even a flash of backlight when powering up.
          but the tv appeas to turn on and i can hear the sound of the menus moving and clicking. i can power down the tv with the button.
          testing the backlights with my tester all 4 strings lit up and showed similar voltage drops. around 110 or so.
          unplug mb and leave only psu plugged into backlights (PSU + BL SELF TEST MODE?) does not light the backlights.
          i do see 24v but 0v on PSON and BLON (i didnt write this down tho so cant be sure)
          with mb connected, PSON...
          11-17-2023, 09:54 PM
        • Superbee_dad
          Sharp 80” long short flash backlight error - Help
          by Superbee_dad
          Hello Sharp TV experts
          Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.

          > I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
          > There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...
          01-24-2025, 11:51 PM
        • ekozeko333
          [Help] Lenovo Yoga Slim 7-14ARE05 (DA0LS3MBAF0) – 25Q80DVN1G Flash Is All FF, USB-C PD Stuck at 5V
          by ekozeko333
          Hi all,
          I’m trying to recover a Lenovo Yoga Slim 7-14ARE05 with board DA0LS3MBAF0 Rev:F. I’ve run into an unusual issue where USB-C PD is stuck at 4.7–5V and the system won’t boot (keyboard lights flash briefly, then nothing).
          🔥 The Problem Started After Suspected ESD/PD Fault
          I experienced a power issue or ESD event through a USB-C charger
          After that, the NX20P5090 power switch was visibly burned and was replaced
          Now the PD controller always negotiates 5V @ 2A, even with known-good chargers
          🧠 What I’ve Done So Far
          Flashed...
          06-21-2025, 02:48 AM
        • corrize
          Nikon D800 camera - flash don’t work and capacitor don’t charge
          by corrize
          Hello, I'm stuck in troubleshooting…
          The flash system works like that : when the (mechanic) flash button is pressed, the flash mecanically pop up, and a circuit buck boost elevate 7v (batt) to 200-300v (?) for charging the big capacitor. And when the photo shoot button is pressed, the capacitor is discharged in the xeon light.

          In the D800, there is a first « power board » close to the battery. 2 wires (batt 7v) goes to another little « flash board ». I measured 7v, so ok.
          When I press the flash button, it's detected by the system, flash icon appear on LDC display....
          10-01-2022, 10:02 AM
        • crozoki
          Philips 65PUS6554/12 one time backlight flash
          by crozoki
          Hello
          I have Philips 65" TV (65PUS6554/12).
          Problem is when turn on tv backlight flash only one time for about 1 second then turns off and display is dark but sound is there.
          Sometimes TV turns on and work with no problem, had backlight and picture, but mostly Tv wont turn on backlight. Any idea where to start looking?

          Power board TPV 715G9187-P01-008-001S
          Main Board 715G9907-M01-B03-005K...
          09-03-2022, 05:47 AM
        • Loading...
        • No more items.
        Working...