Learning from EDN Magazine.
http://www.edn.com/design/analog/443...5a82eca4c0814a
http://www.edn.com/design/analog/443...5a82eca4c0814a
-
Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809 -
Re: Aluminum capacitor slideshow: Handling heat issues
Also, interesting that the sleeve DECREASES the temperature. I mean, it makes sense, but I never thought of that before :P
In a way, "common" sense would have you believe that the sleeve is covering the capacitor, so it must be keeping some of the heat in. Turns out to be incorrect xD
Like, I have always wondered why they stopped painting pole transformers black. It radiates heat much better (also can absorb it better as well... :S)
P.S. I hate how they don't have the slideshow built-in (?) to the web page, it's just a link, so you keep having to reload the rest of the page.Muh-soggy-knee
-
Mounting and Handling Guidelines for TO220 TO220F TO247 Cases / Packages
The TO220, TO220F and TO247 are the popular packages for power devices because of their versatility and ability to dissipate moderate amounts of heat. This application note describes the basic guidelines for handling power MOSFETs in TO220, TO220 and TO247 packages shown in Figure 1. Please note that only mechanical and soldering guidelines are covered here. Additional precautions are required for isolating high voltage rated devices to meet safety regulations.
Securing a good thermal interface between...10-07-2024, 04:35 AM -
Problem
This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached.... -
Hi, I have some 32 bits computer motherboards that need repair, as they fail to
power on.
Here are some examples :
(N.B. "capacitors" indicated here are electrolytic capacitors located in the onboard
switching supply area).
(N.B. #2 : I could not find a 3300 microF aluminum-polymer with a higher voltage
than 6.3 V.)
1 - Motherboard #1 : this is an Asrock K7VT2 (socket A) that still works well. To put it on test
I replaced capacitors with aluminum-polymer.
3300 microF/6.3 V. x 4 replaced by 3300 microF/6.3 V. (KYOCERA... -
Hello,
I have the HP EliteBook 2540P and when I disassembly the screen I cut accidentally one aluminum foil where it was on the top of the one speaker. What is the purpose of these aluminum foils on the top of the speakers.... -
Hi, trying to troubleshoot some problems with this laptop I just finished repairing which had power issues (Burnt Buck converter - SY8883DFC shorted to ground).
After repairing the above issue, I realized the following remaining problem,
Sound only comes from bottom speakers, top palmrest speakers don't work. Neither does the headphone jack (static/buzzing).
The computer recognizes headphones are connected and displays a popup in windows
Sometimes, the computer will boot up and the sound will be working fine. However, if I run intensive programs and the computer...
Comment