"En" or E "pi" caps?
Has anyone heard good or bad about "En" branded cap. Might be E then "pi". Ran across them on an AB-BX6 PII Board. 1000uf 10V (blk/gold letter) and 100uf 16V (blk/ silver letter). The board works and none appear to be bad. It does have 5 Sanyo 1500uf 10V caps near cpu slot.
-
-
Re: "En" or E "pi" caps?
post a pic. -
Re: "En" or E "pi" caps?
Hope photo is clear, had to do some creative microfocus.Attached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Re: "En" or E "pi" caps?
not listed here
http://capacitor.web.fc2.com/
i bet there are mom&pop cap factories in someones basement in china.Comment
-
I know I've been a little scarce lately (like the last 2-3 years), but I'm still here and still doing my thing with fixing PSUs.
For today's considerations, I have a Seasonic B12 BC-550 [A551bcafh] 550 Watt ATX power supply for you (click on links for full size images).
https://www.badcaps.net/filedata/fetch?id=3591771
https://www.badcaps.net/filedata/fetch?id=3591772
It's a modern ATX unit with fixed (non-modular) cables and an 80-plus bronze certificate. Here's the label:
https://www.badcaps.net/filedata/fetch?id=359177... -
Hello,
First, I am a complete noob with high voltage stuff. I'm learning, but I need help by someone looking over my shoulder.
I recently came into posession of a Heathkit IO-4205 5MHz Dual Trace Oscilloscope. The documentation is copyright 1978. I'm told it works.
I opened it up to check the caps before I applied power, and found the following black caps and wanted to know what they were. They are on the power supply board. I was able to read the name and model and came up with, "Nytronics 162J-1, 0.1uF, 20% tolerance, 2000VDC."
... -
I'm trying to repair two old VCRs, they both have bad caps. One has leaky ones, the other would barely run until I subbed in some caps from another power supply I had laying around (though they are the wrong values). This vcr works for an hour or two, but then the power supply starts whining and the picture gets lines in it. I didn't replace all the secondary caps, so another voltage might still be problematic, or the values I used are too far off.
I've been on mouser and digikey but the options are a bit overwhelming. I just need some new ones that will work. They don't need to be top quality,... -
Good evening
I recently aquired a rev 1.1 Gigabyte 60XT, and was suprised of the amount of leaking caps for a motherboard of the P3 era. Especially the way the 330µf caps seems like the housing discolored even.
Now, there are some 3300µF 6.3V KZG series around the CPU. Would it be OK to replace them with something like EEUFR1A332 ? (Panasonic FR 3300µF 10V). Or was this board designed around very low ESR caps?
But I was also suprised about the bigger boys, which are 330µF 25V.
Could it be they used 25V caps because they were cheaper / available at that time?... -
I do have several old pc motherboards which i recapped 10 year ago and some of those caps are bulged now.
I would like to upgrade them using solid capacitors. I do use them for testing and helping some alternative operating systems.
I would like to ask if such an upgrade can be done, what should i have in mind when replacing electrolytic by solid caps and if such thing exist, if there are caps list for old motherboards. I would have to figure out what caps needs each motherboard and then prepare a list to try to ask for them on some electronics stores.
Comment