Hey all... I've been looking everywhere for a solution to this but all I can find from reported issues is the 2 Second to Block issue, however that's not the problem I'm having with this 19" monitor. What happens is whenever you turn it on, it doesn't go black at all... it goes completely white. You can't access any of the OSD menus or anything. I've plugged it into a couple of other computers and still the same issue. I've attempted to change out the VGA cord and still the same problem. The computer its connected to will act as if nothing is wrong with it at all. If the comptuer goes to sleep/screen saver times out the monitor will turn off. If you wake up the comptuer the monitor comes back on but completely white screen. Has anyone else had this issue with this monitor? Is there a way to reset it back to the factory defaults with a button press sequence or something? Any help would be extremely helpful. Would hate to have to throw it away when all that needs to be done is something simple. Thanks ahead of time!
Announcement
Collapse
No announcement yet.
Help with Compaq WF1907 White Screen Issue
Collapse
X
-
Re: Help with Compaq WF1907 White Screen Issue
You need to use a butter knife or flat headed screwdriver to prise the tabs around the edge of the case.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.
Comment
-
Re: Help with Compaq WF1907 White Screen Issue
Ok... got the plastic cover off the back and now I find that the circuit board is rivited behind some metal plates. Photos show what I mean...
How am I suppose to get to the motherboard without doing major damage here? BTW - The 4 screws around the outside edge only remove the plastic outer cover.
Comment
-
Re: Help with Compaq WF1907 White Screen Issue
The prior pics should have been viewable but this time I attached them... hopefully this will explain. The first image shows the rivets pointed out with the bklue arrws and the 4 outer screws in red arrows. (Figured out the problem with the images... forgot to convert them from direct from camera)Last edited by Lrdsatyr8; 09-24-2012, 02:53 PM.
Comment
-
Re: Help with Compaq WF1907 White Screen Issue
Oh my. It looks like they've completely sealed it as if to make it completely unserviceable...
Never seen that before.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.
Comment
-
Re: Help with Compaq WF1907 White Screen Issue
Originally posted by jetadm123 View PostOn your first photo, you have 4 orange arrows pointing at screws or rivets?
That cover looks like one whole unit that may be screwed onto the LCD panel itself. Check along the outer perimeter of the cover for screws.
Comment
-
Re: Help with Compaq WF1907 White Screen Issue
Well.. I finally got this puppy open and got to the circut boards. The first two pics are the power board and the second are the main board. I checked the fuse and now problems there. I also used my multimeter on the back of the power board near the fuse and found no problems there either with any of the smd's. Still trying to figure out what might be happening here. BTW - You were right about the screws on the side after removing the the ones that hold the plastic cover on... I find kinda dumb now! LOL
Comment
-
Re: Help with Compaq WF1907 White Screen Issue
Here are the voltage regulators on the main board.
Test according to:
https://www.badcaps.net/forum/showth...372#post266372Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.
Comment
-
Re: Help with Compaq WF1907 White Screen Issue
Now that you have it opened, there should be another board under a thin metal cover on the top of the monitor - this is the t-con board. On it, you will see a small SMD fuse near the connector, usually marked Fx or similar (where x is a number).
Can't find it yet???
Let's use this pictures as a reference:
https://www.badcaps.net/forum/attach...9&d=1348777759
follow the thin ribbon cable at the bottom of the board, and this will lead you straight to the t-con board.
Comment
-
Re: Help with Compaq WF1907 White Screen Issue
That mean there is a bad short on the T-CON board and proably loading down the 5V power supply. You should disconnecting the ribbon cable to the T-CON then the monitor should turn back on with just white/gray glowing screen, and hopefully it did not damaged the switched transistor on the main baord that supplies the power to the T-CON fuse that is bypassed.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809
Comment
-
Re: Help with Compaq WF1907 White Screen Issue
Originally posted by Lrdsatyr8 View PostOk... I did finally get to the T-Con board... and sure enough, there was a fuse (F1) that was blown. However, I attempted to jump it and now I don't get anything but a flashing power light.
That's a fine way to blow something else too.
Folks, I will repeat this so that hopefully other people reading the forums won't be doing this mistake anymore:
IF A FUSE ON YOUR T-CON IS BLOWN, DO NOT JUMPER, BYPASS, OR SOLDER ACROSS IT WITH WIRE OR HIGHER RATED FUSE!
@ Lrdsatyr8: most likely you have a shorted ceramic cap on the main boosted voltage rail. Post some pictures of the t-con so we can start troubleshooting it.
... and remove that jump across the fuse, please.Last edited by momaka; 10-21-2012, 11:21 AM.
Comment
Comment