Yes, it's fine, I managed to clean the region, it starts up much faster now. However, I had the choice between two region files (see photo). I didn't know what NPDM and YPDM corresponded to. I took the first one, it works perfectly. I'll upload the clean dump to see.
Thanks....
madjid911
Badcaps Veteran
Last Activity: 04-21-2025, 12:57 PM
Joined: 12-10-2016
Location: Roubaix
-
on the other hand it takes a long time to display on first startup could someone clean the intel region?Leave a comment:
-
I tried post 12 everything works thank you very much for sharing...Leave a comment:
-
I tried post 77, it starts several times without display then ends up turning off, so does not work for me, only post 2 works but impossible to make the wifi work, I updated the bios and the wifi card drivers nothing works...Leave a comment:
-
Hello, I have exactly the same problem. I changed the BIOS with post 2, but since then I have been unable to have WiFi. Could someone please clean my original BIOS?...Leave a comment:
-
Post 2 finally worked, thank you....Leave a comment:
-
Hello, can you clean my original bios? The laptop does not start but the eeprom is well supplied with 3V3. I think the bios is corrupted.
I tried positions 1 and 8, there was a small reaction when you plug in the charger but nothing more
ADM80 LA-C642P R1.0
LATITUDE E5570
s/n : 43T0MC2
Thanks...Leave a comment:
-
Thanks for sharing, but the result is the same, it turns on without display, it must have a hardware problem, no one has managed to find out what it is? Maybe reprogram the second chip?...Leave a comment:
-
Hello, I have a Legion 5 that has not started but has no display and the keyboard does not respond, the two bios are well supplied with 1V8. The 3V and 5V are present, the battery charges correctly, the client was playing when the PC suddenly turned off, I did not find a short, when I connect the power supply to the GPU graphics card except immediately, 0.9 ohms but I do not think of a short because it is supplied with 0V7 on the coils, on the other hand the processor is not supplied with power on the coils and does not suffer at all
I think the bios was corrupted, but according to...Leave a comment:
-
Thanks works perfectly for me I was able to remove the bios password...Leave a comment:
-
Hello, can you update my bios with the original version please, my laptop does not display anything on the screen and the eeprom is well supplied in 1V8, I think the bios is corrupted, I attach the original one recovered on the site thank you for your help
I don't know how to convert 331 format to bin format
I tried post 4 it didn't work for me
For Asus G513QR
SN : MANRKD01131G6417...Last edited by madjid911; 03-09-2025, 08:52 AM.Leave a comment:
-
I ordered a new programmed sio, it works, thanks for your helpLeave a comment:
-
I injected voltage on +3VPCU, the SIO IT8987E heated up, I removed it, I no longer have a short circuit, so I have to order a new one, can you tell me if the SIO IT8987E is programmed? Can I buy a blank one?
I have a new SIO IT8528E, IT8587E and IT8518E in stock, can this be compatible?...Leave a comment:
-
PR443 pin 2 : 4,5 ohms, 0V
pin 1 : 55,2komhs 3V28
PQ69 pin 2 : 1V3, PIN 3 : 2V6
PQ63 pin 1 : 3V26; pin 2 : 2V74; pin 3 : short
so I have shorts on +3VPCU ? should I put voltage on it to know where it heats up?...Leave a comment:
-
would that mean my SIO is dead? When I press the power button I don't have the 3v and 5V that triggers, I tried with another keyboard tooLeave a comment:
-
Thanks for the details, I have 3V26 on 51225_LDO3, is it 51225_LDO3 that should power SIO or +3V?...Leave a comment:
-
Asus FX504G no power
Hi, I have an asus laptop FX504G (dabklgmb8d0 rev D) that does not start at all, no signs of life, no liquid damage, no shorts, the processor, the graphics card, the chipset and the SIO micro controller have good resistance.
I have 20V everywhere, on the other hand the SIO micro controller is not powered, there is no +3V, so I changed the "5X=" chip which was not short and well supplied with 20V, the result remains the same, looking at the diagram I see that EN1 and 2 is "S5_ON" (he is at OV), it is a signal that must come from the SIO, isn't it? But then... -
F7000 PIN 2 : 0V700 increasing
pin 1 : 0V...Leave a comment:
-
[B]TBA_VDDA : 5V12
TBA_VDDP : 5V12[/B]
[B]TBA_AUX_DET : 4V94
TBA_CSI_P : 19V77
TBA_CSI_N : 19V77[/B]
[B]SMBUS_SMC_5_G3_SDA : 3V27
SMBUS_SMC_5_G3_SCL: 3V27[/B][B]TBA_VDDA : 5V12
TBA_VDDP : 5V12[/B]
[B]TBA_AUX_DET : 4V94
TBA_CSI_P : 19V77
TBA_CSI_N : 19V77[/B]
[B]SMBUS_SMC_5_G3_SDA : 3V27
SMBUS_SMC_5_G3_SCL: 3V27[/B][B]TBA_VDDA : 5V12
TBA_VDDP : 5V12[/B]
[B]TBA_AUX_DET : 4V94
TBA_CSI_P : 19V77
TBA_CSI_N : 19V77[/B]
[B]SMBUS_SMC_5_G3_SDA...Leave a comment:
-
A1706 No power
Hello, I have a macbook a1706 (820-00923-A) that does not turn on, the 20v ubc triggers but no power consumption, no short and no liquid damage, PPBUS_G3H: 0V15 (16mohms no short), U7000 is well powered by the 20V, I looked at everything around the ISL9239 chip the resistors are good, so I replaced the chip twice but the result is the same, my skills stop there can you help me please?
No activity results to display
Leave a comment: